Laser Technology UltraLyte LR B Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 60

Laser Technology UltraLyte LR B Скачать руководство пользователя страница 35

Section #4 – Instrument Tests

33

Electronic Copy of LTI's UltraLyte LR B User's Manual - 2

nd

Edition © 2002

MENU

LASER

BATT

MPH

KmH

CmS

SPEED

SURVEY

JAM

GSL

TOD

CONT

FMS

DGV

TEST

DBC

DELTA

MUTE

Section #4 – Instrument Tests

There are five tests that allow you to verify the UltraLyte LR B’s
mechanics. These tests include:

•

Display Integrity Test

•

Scope Alignment Test

•

Reference Frequency Test

•

Fixed Distance Test

•

Delta Distance Test

Your UltraLyte LR B may not include the Reference
Frequency Test or the Delta Distance Test. These two
tests are factory-defined options that are set when the
instrument is shipped.

Display Integrity Test

The Display Integrity Test allows you to verify that all display segments
are operating. LTI suggests that you do this test periodically. Refer to
the instructions and Figure 23 below to test the display integrity.

1.

Ensure that the UltraLyte LR B is powered ON.

2.

Press the

TEST OPTIONS button

. The display should look

like Figure 23.

3.

Compare the instrument’s display to the figure above. If any
segment fails to display, contact Laser Technology, Inc. to
arrange for repair. See the inside front cover for LTI contact
information.

You may also test the display integrity at power ON, by
holding the

TRIGGER

(see page 14).

Figure 23. Display Integrity Test

«
...
33
34
35
36
37
...
»

Содержание UltraLyte LR B





























































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды