manualshive.com logo in svg

Lantronix PremierWave, Руководство пользователя

Поделиться
Скачать
Lantronix PremierWave Скачать руководство пользователя страница 69

7: Line and Tunnel Settings

PremierWave® EN Embedded System on Module User Guide

69

Protocol

Set the operational protocol for the Line. The default is Tunnel. Choices are:

None

Modbus RTU

Modbus ASCII

Tunnel

 = Serial-Network tunneling protocol.

Baud Rate

Set the Baud Rate (speed) of the Line.  The default is 

9600

.

Any set speed between 300 and 921600 may be selected: 300, 600, 1200, 
2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600.  
When selecting a Custom baud rate, you may manually enter any value 
between 300 and 5000000.  

Note:

 Custom baud rates are not supported when a line is configured for 

Command Mode.   For Interface type USB-CDC-ACM (Line 3 only), this 
setting is irrelevant.

Parity

Set the Parity of the Line. The default is 

None

.

Note:

For Interface type USB-CDC-ACM (Line 3 only), this setting is 

irrelevant.

Data Bits

Set the number of data bits for the Line. The default is 

8

.

Note:

For Interface type USB-CDC-ACM (Line 3 only), this setting is 

irrelevant.

Stop Bits

Set the number of stop bits for the Line. The default is 

1

.

Note:

For Interface type USB-CDC-ACM (Line 3 only), this setting is 

irrelevant.

Flow Control

Set the flow control for the Line. The default is 

None

.

Note:

For Interface type USB-CDC-ACM (Line 3 only), this setting is 

irrelevant.

Note:

This field becomes available if RS232 or RS485 Full-Duplex is 

selected under Interface above.

Xon Char

Set Xon Char to be used when Flow Control is set to Software.  Prefix decimal 
with \ or prefix hexadecimal with 0x or prefix a single control character 
<control>. 

Note:

This field becomes available for configuration when Software is 

selected under Flow Control.

Xoff Char

Set Xoff Char to be used when Flow Control is set to Software.  Prefix decimal 
with \ or prefix hexadecimal with 0x or prefix a single control character 
<control>. 

Note:

This field becomes available for configuration when Software is 

selected under Flow Control.

Gap Timer

Set the Gap Timer delay to Set the number of milliseconds to pass from the 
last character received before the driver forwards the received serial bytes.  
By default, the delay is four character periods at the current baud rate 
(minimum 1 msec). 

Threshold

Set the number of threshold bytes which need to be received in order for the 
driver to forward received characters.

Line Settings 

Description

Содержание PremierWave


















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды