Lantronix Open-Q 2100 Скачать руководство пользователя страница 44

Страница: 44 / 45

Open-Q 2100 Development Kit

Open-Q™ 2100 Dev Kit User Guide

3.9.21

Ethernet connector J2801

Figure 29 J2801 Ethernet connector

J2801 (Ethernet connector) provides 10/100 Ethernet connectivity to the Open-Q 2100 Development kit via

LAN9514 USB-to-Ethernet Hub. Please note that the USB hub and Ethernet features is not available when

micro-B USB cable is plugged in the ADB (Recovery) J2800 port.

3.9.22

Power probe J202

Figure 30 J202 Power probe connector

J202 (Power probe connector) provides method of measuring power consumption of Open-Q 2100 SOM. The

0.01R sense resistor is placed in series on the VPH_PWR rail to provide method of current consumption

measurement. The pin configuration of three pin header is given in the table below:

Table 3.9-10 Power probe J202 Pin out

Description

Signal

Pin Number

Current sense negative

CSN

J202[1]

Current sense positive

CSP

J202[2]

Ground

GND

J202[3]

Pin 1.

Содержание Open-Q 2100














































Результаты поиска

Содержание Open-Q 2100

Отзывы:

Похожие инструкции для Open-Q 2100

Бренды по названию

Популярные бренды

Lantronix Open-Q 2100, Руководство пользователя

Результаты поиска

Содержание Open-Q 2100

Отзывы:

Похожие инструкции для Open-Q 2100

Бренды по названию

Популярные бренды