Lantronix Open-Q 2100 Скачать руководство пользователя страница 23

Страница: 23 / 45

Open-Q 2100 Development Kit

Open-Q™ 2100 Dev Kit User Guide

Table 3.9-3 Dip Switch HW / SW configuration

Function

DIP Switch

Description

Notes

FORCE USB

BOOT

S1700-1

Toggles between FORCE USB boot

and EDL mode. Enables FORCE

USB (GPIO37) when DIP switch is

turned ON for boot recovery

purposes.

Default out of the box

configuration is OFF.

NOTE:

FORCE USB boot option

is reserved for use by Lantronix

only for boot recovery purposes.

BOOT

CONFIG1

S1700-2

Enables APQ boot configuration 1

when DIP switch is turned ON.

Controlled by APQ GPIO77. See

schematic for boot configuration

options.

Default out of the box

configuration is OFF

Warning!

Before making any changes to the dip switch, make sure to note down the previous configuration.

The default switch settings are above.

3.9.3 Carrier Board Expansion Connectors

The following table lists the connectors, expansions and their usages on the carrier board:

Table 3.9-4 Carrier Board Expansion Options and Usage

Domain

Description

Specification

Usage

Power

DC / Barrel charger

12 V DC Power Supply

3 A

Power Supply

Battery Connector

6 pin header

For Battery operation

and charging

development

Debug Serial via USB

Debug Serial UART

console over USB for

development

USB Micro B connector

Development Serial

Connector for debug

output via USB

Buttons

General Purpose SW

button

SMD Button

Additional button for

general purpose

(connected to

APQ_GPIO87)

Содержание Open-Q 2100














































Результаты поиска

Содержание Open-Q 2100

Отзывы:

Похожие инструкции для Open-Q 2100

Бренды по названию

Популярные бренды

Lantronix Open-Q 2100, Руководство пользователя

Результаты поиска

Содержание Open-Q 2100

Отзывы:

Похожие инструкции для Open-Q 2100

Бренды по названию

Популярные бренды