Lanier AP2145 Скачать руководство пользователя страница 235

Страница: 235 / 424

vii

Configuring the machine as a remote printer

If a dedicated NetWare print server is being used, the machine should be config-
ured as a remote printer.

The actual procedures for configuring the machine depend on the NetWare ver-
sion.
• NetWare 3.x

⇒

p.47 “Setting Up as a Remote Printer”

• NetWare 4.x, 5/5.1

⇒

p.55 “Setting Up as a Remote Printer”

Macintosh

For setting up the machine as a network printer in a Macintosh environment, see
p.61 “Macintosh Configuration”.

NetWare
Print Server

NetWare
File Server

Remote Printer

Windows 95 / 98/Me

Windows 2000

Windows NT 4.0

AppleTalk

Macintosh

Содержание AP2145





































































































































































































































































































































































































































Результаты поиска

Содержание AP2145

Отзывы:

Бренды по названию

Популярные бренды

Lanier AP2145, Руководство по установке

Результаты поиска

Содержание AP2145

Отзывы:

Бренды по названию

Популярные бренды