Lanier AP2145 Скачать руководство пользователя страница 16

Страница: 16 / 424

Getting Started

Guide to This Printer

Mainframe

Exterior: Front View

Printer Board

Remove this board when installing some
options.

Parallel Interface Connector

Plug the parallel cable, which connects
the printer to your computer, into this
socket.

Ethernet Cable Connector

Plug the Ethernet cable, which connects
the printer to the network, into this sock-
et.

HDD (Option) Slot

Set the optional Printer Hard Disk.

⇒

p.18 “Installing Printer Hard Disk

Type4510”

Power Switch

Use this switch to turn the printer power
on and off.

Output Tray

Printed output is stacked here with the
print side face down.

Control Panel

Contains keys for printing operation and
a panel display that shows the printer
status.

⇒

p.9 “Control Panel”

Front Cover

Open this cover if you replace some parts
or if a paper misfeed occurs.

Paper Tray

Holds up to 500 sheets of plain paper per
tray and 1000 sheets in total. (80 g/m

, 20

lb. bond)

10.

Paper Bank PS430 (Option)

Holds up to 500 sheets of plain paper per
tray and 1000 sheets in total. (80 g/m

, 20

lb. bond)

⇒

p.15 “Installing Paper Bank PS430”

AP3ENSetup-F-ricoh_FM.book Page 6 Friday, October 5, 2001 2:43 PM

Содержание AP2145





































































































































































































































































































































































































































Результаты поиска

Содержание AP2145

Отзывы:

Бренды по названию

Популярные бренды

Lanier AP2145, Руководство по установке

Результаты поиска

Содержание AP2145

Отзывы:

Бренды по названию

Популярные бренды