manualshive.com logo in svg

Lanier R/C MARINER .120, Руководство по сборке

Поделиться
Скачать
Lanier R/C MARINER .120 Скачать руководство пользователя страница 14

                                                       Assembly Instructions

 

 

 

LANIER R/C    

MARINER

 .120 

          

               
           LANIER R/C, INC.- P O Box 458 - Oakwood, GA  30566 - Ph 770-532-6401 

!

  Copyright 2002  Lanier R/C, Inc.

 

14 

 

 
2.  Notch out for mast to allow for cowl 
adjustment fore and aft if necessary. 

 
 

 

 

 

 

3.  Using a piece of cardboard, the height of the 

pod, mark two hole, 1/8” in from the front edge 
and 5/8” from top and 5/8” from bottom. Tape it 
to the pod with the front edge flush with the 

firewall.  You will also need one for the other 
side. 

 

 

 
4.  Slide the cowl on to the pod under the 

templates.  Temporarily set the engine in the 
mount.   Mount the spinner back plate on the 
engine crankshaft with prop to hold it in place.  

Adjust the cowl so that you have 3/32” 
clearance between it and the back plate.  Now 

tape the cowl to the pod. 
 

 

 

Содержание MARINER .120
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды