manualshive.com logo in svg

Lanier R/C MARINER .120, Руководство по сборке

Поделиться
Скачать
Lanier R/C MARINER .120 Скачать руководство пользователя страница 11

                                                       Assembly Instructions

 

 

 

LANIER R/C    

MARINER

 .120 

          

               
           LANIER R/C, INC.- P O Box 458 - Oakwood, GA  30566 - Ph 770-532-6401 

!

  Copyright 2002  Lanier R/C, Inc.

 

11 

 

 

 

 

 
2.  Using 5 min. epoxy, glue one long rail 
against the forward edge of the bulkhead as 

shown.  Glue the two short pieces under the rail, 
against the sides, and parallel with the bottom 
edge of the wing saddle doubler.  Glue the 

forward rail in place.  Use a servo to get the 
proper spacing required. 
 

 

 

3.  Locate the pushrod material.  Cut 2 pieces 

from the outer sleeving 22-1/2” long.  Cut the 
long carbon fiber pushrod into 2 – 24-1/4” 
pieces.  Screw the short threaded rods into one 

end of the pushrod 3/8”. Install the hex nut and 
screw on a clevis.  Do two pushrods. 

4.  Prepare the other end of the pushrods that 
will hook up to the servo arms.  Locate two 4” x 
4-40 rods threaded on both ends.  Screw them 

in 3/8” on both pushrods. 
 
5.  Uncover the pushrod exit holes in the aft end 

of the fuselage.  Enlarge them so the pushrod 
sleeving will fit using a motor burring tool or 
Exacto blade.  Push the sleeving in leaving 

approx. 1” extending.  Using Silicone Sealer, 
glue them in place both sides. 
 

 

 
6. Mount both pushrods in the sleeves and hook 
up to control horns on rudder and elevator.  

Place a hex nut and clevis on each. 
 

Содержание MARINER .120
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды