manualshive.com logo in svg

Lanier R/C MARINER .120, Руководство по сборке

Поделиться
Скачать
Lanier R/C MARINER .120 Скачать руководство пользователя страница 10

                                                       Assembly Instructions

 

 

 

LANIER R/C    

MARINER

 .120 

          

               
           LANIER R/C, INC.- P O Box 458 - Oakwood, GA  30566 - Ph 770-532-6401 

!

  Copyright 2002  Lanier R/C, Inc.

 

10 

 

 

HINGING THE ELEVATOR AND RUDDER

 

 

 

 
14.   Before hinging the elevator and rudder to 

the stab and vertical fin, locate the control horns 
and CA them in place with thin CA.  Match drill 

the holes and complete mounting with hardware   
supplied. 
 

 

 

15. Locate the control horn as shown in photo.  
Locate rudder control horn 4-1/4” from bottom 
edge of rudder.  

Make sure rudder and 

elevator control horns are on opposite 
sides. 

 

 

 
15.    Locate  the  sub-dorsal  fin.    Draw  a  center 

line on the bottom of the hull, remove the 
covering the width and length of the fin.  Install 

the hinge in the rudder and epoxy the fin in 
place.  The rudder and hinge will keep it 
vertical.  Tape the forward end to maintain 

alignment.  Note: it may be necessary to slot the 
sub-dorsal fin for the hinge placement. 
 

16.  Install rudder and elevator and CA, with 
thin CA, as described when installing ailerons. 

 

INSTALLING SERVOS AND PUSHRODS 

 
1.  Locate the 3/8” sq. x 24” pieces of wood.  

Cut 2 pieces 2-1/2” long.  Now cut 2 more 
pieces 6-3/4” long. 
 

 

Содержание MARINER .120
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды