manualshive.com logo in svg

Lanier R/C MARINER .120, Руководство по сборке

Поделиться
Скачать
Lanier R/C MARINER .120 Скачать руководство пользователя страница 1

                                                       Assembly Instructions

 

 

 

LANIER R/C    

MARINER

 .120 

          

               
           LANIER R/C, INC.- P O Box 458 - Oakwood, GA  30566 - Ph 770-532-6401 

!

  Copyright 2002  Lanier R/C, Inc.

 

1 

 

 

Wingspan....

80”                                        

Wing Loading…

24 - 28 oz./sq. ft.

 

Fuselage Length…

65”                         

Wing Area…

1140 sq. in. 

Engine Required ...

 

2-Stroke .91 to .120     Four stroke  .120 to .180                                                                                                       

Weight……..

12 - 14 lbs.

 

 

WARRANTY

 ……………… Lanier R/C is proud of the care and attention that goes into the manufacture of parts for 

its model kits.  The company warrants that for a period of 

3

0 days, it will replace, at the buyers request, any parts or 

material shown to the company's satisfaction to have been defective in workmanship or material at the time of 
purchase.

 

 
No other warranty of any kind, expressed or implied, is made with respect to the merchandise sold by the company.  
The buyer acknowledges and understands that he is purchasing only a component kit from which the buyer will 
himself construct a finished flying model airplane.  The company is neither the manufacturer of such a flying model 
airplane, nor a seller of it.  The buyer hereby assumes the risk and all liability for personal or property damage or 
injury arising out of the buyers use of the components or the finished flying model airplane, whenever any such 
damage or injury shall occur. 
 
Any action brought forth against the company, based on the breach of the contract of sale to the buyer, or on any 
alleged warranty there under, must be brought within/ year of the date of such sale, or there after be barred.  This 
one year limitation is imposed by agreement of the parties as permitted by the laws of the state of Georgia. 
 

Содержание MARINER .120
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды