Landoll 325C Скачать руководство пользователя страница 70

Страница: 70 / 80

5-2

TIRES - WHEELS - SUSPENSION

Most tire, wheel, and suspension related problems are due to excessive loads, extreme conditions, and

improper maintenance. Tire, wheel, and suspension problems can be easily detected and solved by check-
ing the following guide.

SYMPTOM

PROBLEM: REMEDY

VIBRATIONS WHILE DRIVING

Improper tire inflation:

inflate to proper pressure.

Tires cupped or have flat spots:

replace tires.

Wheels bent or loose:

replace or tighten.

Tires incorrectly mounted:

remount.

Mud in wheels:

clean wheels.

Tire(s) out of balance:

balance tires.

Brakes dragging:

locate cause and repair.

Object(s) stuck between duals:

remove object(s).

RAPID TIRE WEAR/
DETERIORATION:

CENTER TREAD WEAR

Over inflation:

deflate to correct inflation.

SHOULDER TREAD WEAR - BOTH
SHOULDERS

Under inflation:

increase inflation to correct PSI. Check axle

alignment.

Overload:

loads are above rated tire capacity. DO NOT load above

rated tire capacity.

SHOULDER TREAD WEAR - ONE
SHOULDER

Axle damage:

straighten or replace axle.

Axles not parallel:

check axle alignment.

OVERALL TREAD WEAR

Overloading:

check tire load rating.

High speeds:

adjust speed according to road and load conditions.

Incorrect dual matching:

properly match dual tires.

Front and rear axle suspension air bags not inflated:

Adjust

front and rear axle ride height control valves to proper settings.

TIRE FLAT SPOTS

Quick stops:

adjust braking practices.

Grabbing brakes:

adjust brakes properly.

Worn or loose wheel bearings:

adjust or replace as needed.

Out of balance wheels and tire:

balance wheels and tires.

Check ABS system function.

Front and rear axle suspension air bags not inflated:

Adjust

front and rear axle ride height control valves to proper settings.

UNEVEN WEAR

Suspension bushings worn:

replace bushings.

Worn or loose wheel bearings:

adjust or replace as needed.

Out of balance wheels and tires:

balance wheels and tires.

5-2

Содержание 325C

















































































Результаты поиска

Содержание 325C

Отзывы:

Бренды по названию

Популярные бренды

Landoll 325C, Руководство оператора

Результаты поиска

Содержание 325C

Отзывы:

Бренды по названию

Популярные бренды