manualshive.com logo in svg

L&L EASY-FIRE e18S, Сборка

Соберите свою печь L&L EASY-FIRE e18S с легкостью, следуя инструкции в бесплатном руководстве. Скачайте его с нашего веб-сайта manualshive.com и наслаждайтесь удобством сборки вашего нового устройства. Доступно для загрузки.

Поделиться
Скачать
background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf 

3/1/2007 Rev 1.3 

Page 7

 

2007  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  P:856.294.0077  F:856.294.0070  [email protected]   hotkilns.com 

  

REMOVING THE CONTROL PANEL 
AND ELEMENT COVER AS ONE 
ASSEMBLY

You  have  two  choices . You  can  remove  the  Control 
Box and Element Cover Box as ONE assembly or you 
can  first  remove  the  Control  Box  from  the  Element 
Cover Box and then remove the Element Cover Box . 
The easiest method, in our opinion, is to remove the 
whole assembly . However, both methods are given .

1) Remove the two screws, that hold the outer portion 
of the control panel to the element terminal box .

Removing the two screws that hold the control 
panel on:

2)  Hinge  the  dynatrol  portion  of  the  control  panel 
down exposing the wire connection terminals . 

The Control Panel Hinged down:

3) Remove the wires numbered  1 through 6  from the 
left side of the Power Terminal Strip and the right side 
of Thermocouple Terminal Strip .

Wires shown removed:

4) Loosen - but do not remove - the four or six screws 
that hold the Element Cover Box to the kiln .

The tear-drop holes on the Element Cover Box 
will allow you to remove it without having to take 
the screws out:

5) Hold the whole assembly and gently lift up so that 

ASSEMBLING YOUR L&L EASY-FIRE KILN

Содержание EASY-FIRE e18S


















Отзывы:

Нет отзывов

Похожие инструкции для EASY-FIRE e18S

Бренды по названию

Популярные бренды

Загрузить еще бренды