manualshive.com logo in svg

L&L EASY-FIRE e18S, Сборка

Соберите свою печь L&L EASY-FIRE e18S с легкостью, следуя инструкции в бесплатном руководстве. Скачайте его с нашего веб-сайта manualshive.com и наслаждайтесь удобством сборки вашего нового устройства. Доступно для загрузки.

Поделиться
Скачать
background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf 

3/1/2007 Rev 1.3 

Page 12

 

2007  

 

L&L Kiln Mfg, Inc.  505 Sharptown Rd, Swedesboro NJ 08085  P:856.294.0077  F:856.294.0070  [email protected]   hotkilns.com 

  

6) Place the kiln section with the #4 & #3 on the ther-
mocouple lead wire on next .

7) Place the kiln section with the #1 & #2 on the TC 
wire on the top ring of the stack . 

8) You are now ready to reattach the hinge . 

SETTING UP THE HINGE

1) Notice that on the back of the kiln that the mounting 

screws for the hinge line up.

2) Take the large ring hinge piece and drop it onto 

the screws on the kiln sections. If the screws on the 

kiln don't perfectly line up with the holes in the large 

hinge piece gently maneuver the hinge piece until 

you have all the screw heads into the keyhole slots 

on the large hinge piece.  

Let the piece drop to 

the top of the slot and rest but do not tighten the 

screws at this time. 

3) Place the kiln door with the hinge top hinge piece 

attached inside the large hinge piece on top of the 

kiln. 

ASSEMBLING YOUR L&L EASY-FIRE KILN

Содержание EASY-FIRE e18S


















Отзывы:

Нет отзывов

Похожие инструкции для EASY-FIRE e18S

Бренды по названию

Популярные бренды

Загрузить еще бренды