L&L EASY-FIRE e18S Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 17

background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf

3/1/2007 Rev 1.3

Page 1



2007

L&L Kiln Mfg, Inc. 505 Sharptown Rd, Swedesboro NJ 08085 P:856.294.0077 F:856.294.0070 [email protected] hotkilns.com

13) Push the spring into one of the two slotted holes
on the side of the large hinge piece . The slot closest to
the kiln will put more tension on the spring . (Note - it
is hard to get the spring into this slot when working
from above) .

Below is a view from the top looking down into
the hinge box. NOTE: When removing the hinge
- use the reverse procedure and be sure to use
the special tool provided.

13) The hinge is now operational .

14) Raise and lower the hinge a few times .

15) Double check to make sure that each end of the
spring is through the appropriate hole in the ring
hinge piece .

16) Open the lid to the full open position and insert the
safety pin to keep the lid locked in the up position .

17) You are now ready to reassemble the panel onto
the kiln .

REASSEMBLING THE CONTROL
PANEL

1) Take the Control Box and Element Cover Box
Assembly and place it on the screws on the

left

hand

side of the element connection terminals (facing from
the front) .

2) Push the whole assembly off to the side left side
slightly so you can access the wires and push them
through the holes .

ASSEMBLING YOUR L&L EASY-FIRE KILN

«
...
13
14
15
16
17
»

Содержание EASY-FIRE e18S


















Отзывы:

Нет отзывов

Похожие инструкции для EASY-FIRE e18S

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды