L&L EASY-FIRE e18S Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 17

background image

ASSEMBLING YOUR L&L EASY-FIRE KILN

easy-fire-install.pdf

3/1/2007 Rev 1.3

Page 10



2007

L&L Kiln Mfg, Inc. 505 Sharptown Rd, Swedesboro NJ 08085 P:856.294.0077 F:856.294.0070 [email protected] hotkilns.com

3) Gently push the right hand side of the element box
away from the kiln sections . This will give you access
to pull the element and thermocouple connection
wires through the element box .

The Element Terminal Box swings over to the left
side exposing the wires :

4) Pull the power and thermocouple wires out .

Pulling the wires out from the back of the
terminal box:

5) Gently lift the element box up and remove from the
kiln sections .

Removing the Terminal Box form the kiln:

6) You are now ready to set up the kiln .

LOCATING THE KILN

1) Place the stand on the floor in the desired location .
This should be set so that the outside stainless steel
surface of the kiln will be at least 12” to 18” from any
combustible wall . Floor must be nonflammable .

Information  concerning  clearances,  ventila-
tion  and  electrical  requirements  is  detailed  in
the  INSTALLATION  Section  of  this  manual .
Read  now  if  you  are  uncertain  about  any  of
these  issues .  DON’T  PROCEED  UNTIL  YOU
ARE COMFORTABLE WITH THE LOCATION

2) Place bottom floor section of kiln on the steel stand
making certain it is centered properly .

3) Note that the kiln bottom is packed on top of the kiln
- so it is easily removed first without moving the kiln .

ASSEMBLING YOUR L&L EASY-FIRE KILN

«
...
8
9
10
11
12
...
»

Содержание EASY-FIRE e18S


















Отзывы:

Нет отзывов

Похожие инструкции для EASY-FIRE e18S

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды