Landia POP-1 страница 62 Скачать руководство пользователя | Manualshive

Страница: 62 / 127

background image

AA02B.C01

Service instruction POPR-I

Page 7/7

Executed by: AJ/CML

Issued on: 12. March 2003

Accepted by: SL/KT

Rev. date: 12 March 2021

Note

End cover, oil chamber and gear must be turned

anti-clockwise

as much as possible, seen from the end of the

propeller, in order to balance the clearance in the bolt holes before the final tightening of the bolts.
After installing the bearing flange control the axial clearance; as stated in the table below.

Motorseries

Acceptable clearance

ms100

0.9 ± 0.05 mm

ms132

1.0 ± 0.05 mm

ms160

1.1 ± 0.05 mm

ms180

1.5 ± 0.05 mm

Installation of mechanical shaft seals

When installing the mechanical shaft seals please be aware that these are precision products and that they
should be handled as such. The slide faces must be protected during the installation.

B.  Stationary sealing ring
C.  Rotating sealing ring
D.  Locking ring
E.  Shaft
F.  Propeller hub

Push  the  stationary  sealing  ring,  pos.
B, into place. Be careful not to damage
the  slide  face  during  the  installation.
When  the  stationary  part  is  mounted
and  straightened  with  a  dial  gauge,
wipe it off with degreaser.

The  rotating  sealing  ring,  pos.  C,  is
inserted  over  the  shaft.  To  ease  the  installation,  put  soap  water  on  the  interior
side of the rubber bellows as well as on the shaft. Do not apply silicone, PTFE
lubricants or oil as they will prevent the rubber bellows from sticking to the shaft.
Installation arbour should be used.
The propeller hub, pos. F, keeps the outer mechanical shaft seal in place. This
happens when the propeller hub is tightened against the output shaft collar.  At
the  inner  mechanical  shaft  seal  the  locking  ring,  pos.  D,  must  be  put  on  the
shaft and the seal pressed together until the locking ring snaps into the locking
ring groove. Inspect the sealing by turning the motor shaft.

Test the mixer for leakage by submerging it and by putting the motor casing and
the  oil chamber under pressure. The pressure is to  be approx.  1  bar.  Leakage
(air bubbles) must not appear. Oil is filled into the oil chamber/gear. During the
filling the mixer must be in a horizontal position.
Oil quantity: see spare parts list.

We reserve the right to technical alterations. Translated from Danish.

A. Bearing flange

«
...
60
61
62
63
64
...
»

Содержание POP-1
































































































































Отзывы:

Нет отзывов

Похожие инструкции для POP-1

Бренд: Yamaha Страницы: 277

Бренд: Tascam Страницы: 38

Бренд: Tascam Страницы: 28

Бренд: Tascam Страницы: 146

Бренд: Tascam Страницы: 16

Бренд: Tascam Страницы: 12

Бренд: Tapco Страницы: 4

Design Mixer Advanced Electronic

Бренд: Gastroback Страницы: 72

Бренд: Carat Страницы: 44

Бренд: Beper Страницы: 64

Бренд: Laney Страницы: 6

Mackie Control Universal Pro

Бренд: Mackie Страницы: 12

Бренд: Dash Страницы: 17

Бренд: Racing Страницы: 23

Бренд: Zelmer Страницы: 52

Бренд: Far Tools Страницы: 13

KHM3WH - Hand Mixer

Бренд: KitchenAid Страницы: 3

Бренд: VADO Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды