Land Pride Rear Blades RBT4596 Скачать руководство пользователя страница 23

Страница: 23 / 38

Section 3: Adjustments

RBT4596 & RBT45108 Rear Blades 301-205M

1/13/21

Table of Contents

Section 3:

Adjustments

Safety First

WARNING

To avoid serious injury or death:

•

Do not allow anyone to go near the blade while grading and

operating the controls. A person can be crushed by the unit.

•

Avoid injury from a falling blade. Always check to make

sure all hardware is secured before adjusting the blade.

•

Never fully extend or retract hydraulic cylinder(s) without

first checking to make sure the implement does not make

contact with tractor tires. Extending implement into the

tractor tires can result in loss of control and damage to the

implement and/or tractor.

Blade Offset Adjustment

Manual Offset

Refer to Figure 2-1 on page 14:

The blade offset has 15 adjustments up to 35" left or right.

(Center position, 7 positions right and 7 positions left.)
1. Read and follow

“Safety First”

on this page before

offsetting the blade.

2. Manually adjust blade offset by removing hitch

pin (#2) and moving outer link (#3) to a different hole

position.

3. Replace hitch pin and secure with hair pin

cotter (#5).

Hydraulic Offset

Refer to Figure 1-3 on page 12:

The blade can be offset hydraulically by as much as 35"

to the right or left with the offset cylinder.
1. Read and follow

“Safety First”

on this page before

offsetting the blade.

2. If offset cylinder is attached to the selector valve,

make certain its lever is set to operate that cylinder.

3. Operate tractor control lever to change blade offset

by as much as 35" right or left.

Blade Angle and Reversing

Manual Angle and Reversing

Refer to Figure 2-1 on page 14:

There are 15 blade angle positions; up to 45 degrees

right or left. (Center position, 7 clockwise positions and

7 counterclockwise positions.)
1. Read and follow

“Safety First”

on this page before

angling the blade.

2. Adjust blade angle by removing hitch pin (#2) and

moving outer link (#3) to a different hole position.

3. Replace hitch pin and secure with hair pin

cotter (#5).

4. The blade may also be rotated around 180 degrees.

a. Disconnect angling link from blade turntable lug.
b. Rotate Rear Blade clockwise 180 degrees.
c. Reconnect angling link to turntable lug.

Hydraulic Angle and Reversing

Refer to Figure 1-4 on page 12:

Adjust blade angle with angling cylinder by as much as

45 degrees clockwise and counterclockwise.
1. Read and follow

“Safety First”

on this page before

angling the blade.

2. If angling cylinder is attached to the selector valve,

make certain its lever is set to operate that cylinder.

3. Operate tractor control lever to change blade angle

by as much as 45 degrees forward or backward.

4. The blade may also be rotated 180 degrees.

a. Disconnect rod end of angle cylinder from blade

turntable lug.

b. Rotate 3-Way Rear Blade clockwise 180 degrees.
c. Reconnect angle cylinder to turntable lug.

IMPORTANT:

Make sure angling link is installed

correctly before using the blade. If not the blade and/

or angle cylinder can be damaged.

IMPORTANT:

Make sure angle cylinder is installed

correctly before using the blade. If not, the blade

and/or angle cylinder can be damaged.

IMPORTANT:

Be careful not to over retract angle

and/or tilt cylinders. Doing so, can cause the

moldboard to come against the angle cylinder and

cause damage to the cylinder and/or blade.

Содержание Rear Blades RBT4596







































Результаты поиска

Содержание Rear Blades RBT4596

Отзывы:

Похожие инструкции для Rear Blades RBT4596

Бренды по названию

Популярные бренды

Land Pride Rear Blades RBT4596, Руководство оператора

Результаты поиска

Содержание Rear Blades RBT4596

Отзывы:

Похожие инструкции для Rear Blades RBT4596

Бренды по названию

Популярные бренды