Land Pride Rear Blades RBT4596 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 38

background image

Section 1: Assembly & Set-Up

RBT4596 & RBT45108 Rear Blades 301-205M

1/13/21

13

Table of Contents

Blade Tilting Cylinder

Refer to Figure 1-5:

WARNING

!

To avoid serious injury or death:

•

Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic

cylinders have been installed and cylinders have been

charged with oil.

•

The Rear Blade may be unstable and hard to control until

all the hydraulic cylinders have been purged with oil.

IMPORTANT:

The blade tilt cylinder receives a 90

degree elbow with a small orifice in one end of the

elbow. Make sure this orifice elbow is installed in the

cylinder port at the rod end of the tilt cylinder.

IMPORTANT:

Attach cylinder base to the upper

cylinder mount. The base will interfere with the

moldboard if attached to the lower cylinder mount.

Hydraulic Blade Offsetting and Angling

Figure 1-5

9

24995

SHIPPING BLOCK
DO NOT REMOVE UNTIL AFTER ALL HYDRAULIC
CYLINDERS, RATCHET JACKS AND/OR MANUAL
LINKS HAVE BEEN INSTALLED.

1. Install a 90 degree elbow (#5) with 3/32" orifice (#4)

into the cylinder port located at the rod end as shown.

Tighten as needed.

2. Install a second 90 degree elbow (#6) without an

orifice into the cylinder port located at the base

shown. Tighten as needed.

3. Screw 111" long hydraulic hoses (#7) into

elbows (#5 & #6) and tighten.

4. Thread adapter fittings (#8) to the other end of the

hydraulic hoses (#7) and tighten.

5. Thread quick disconnect couplers (#9) to adapter

fittings (#8).

6. Attach hydraulic cylinder (#3) to the lugs at the back

of the blade with clevis pins (#2). Make sure hydraulic

ports are positioned on the back and the cylinder

base is mounted to the center lug as shown.

7.

Secure clevis pins with hair pin cotters (#1).

8. Route hoses through hose brackets located on the

main frame and hitch. Connect hoses to tractor's

hydraulic system.

9. Remove shipping block at this time.

«
...
15
16
17
18
19
...
»

Содержание Rear Blades RBT4596







































Отзывы:

Нет отзывов

Похожие инструкции для Rear Blades RBT4596

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: Cannon Страницы: 40

Бренд: NARGESA Страницы: 34

Бренд: Eaton Страницы: 21

Бренд: NANO Страницы: 4

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

Бренд: Keithley Страницы: 79

Бренд: Kayakpro Страницы: 17

Бренд: Yoshitake Страницы: 11

Бренд: National Instruments Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды