Land Pride Rear Blades RBT4596 Скачать руководство пользователя страница 14

Страница: 14 / 38

Section 1: Assembly & Set-Up

RBT4596 & RBT45108

Rear Blades 301-205M

1/13/21

Table of Contents

Rear Blade Assembly

Figure 1-1

18767

SHIPPING BLOCK
DO NOT REMOVE UNTIL AFTER ALL HYDRAULIC
CYLINDERS AND/OR RATCHET JACK AND
MANUAL LINKS HAVE BEEN INSTALLED.

Assembly & Set-Up Safety

WARNING

To avoid serious injury or death:
Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

DANGER

To avoid serious injury or death:

•

Always check all blade hardware for tightness before

moving or working around the unit. Make sure moldboard

pivot and tilt retaining hardware is tightened to the correct

torque. The moldboard can fall from the its pivot mount or

tilt mount if retaining hardware is loose or missing.

•

Components falling from the implement can injure a

person. Make certain all components are secured to the

implement before lifting it, and that the unit is properly

supported on the ground before removing lifting device.

Always keep feet and other extremities clear of areas where

components can fall.

Hitch, Frame & Blade

Refer to Figure 1-1:

1. Locate shipping crate on a level surface. Remove &

separate blade assemblies from shipping crate.

2. Use a lifting device to set blade pivot assembly (#8)

upright. Remove bolts (#5), lock washers (#6) & pivot

cap (#9) from blade pivot assembly (#8).

Do not

remove shipping block in the blade tilt housing.

3. Carefully insert blade pivot assembly (#8) into main

frame (#2) at a 90° angle to the frame.

4. Reinstall pivot cap (#9), lock washers (#6), and

3/4"-16 x 1 3/4" GR5 hex head cap screws (#5).

Tighten hardware to secure main frame to blade pivot

assembly.

5. Remove 3/4" x 4 3/8" hitch pin (#10) and rotate jack

stand (#11) to a vertical position. Re-insert pin with

lock pin.

6. Lower unit to ground and unhook lifting device.
7.

Remove front pivot shaft (#3) from front hitch

assembly (#1) by removing 1/2" bolts (#4).

8. Secure front hitch assembly (#1) to a lifting device or

attach to a tractor. Refer to

“3-Point Hook-Up”

page 11.

9. Insert main frame (#2) into front hitch (#1) as shown.

Reinstall front pivot shaft (#3) and secure with

1/2"-13 x 1 1/2" GR5 bolts (#4). Tighten the hardware

to secure front pivot shaft (#3).

10. If not already done, attach unit to tractor 3-Point

hitch. The top 3-Point hitch pin and linchpin are to be

supplied by the customer. See Figure 1-2 for

category settings.

11. Re-check all hardware for tightness. Torque all bolts

to specifications as listed in the

“Torque Values

Chart”

on page 31.

12. Check blade pivot bolts (#5) and blade tilt bolts (#7)

for tightness. If needed, tighten bolts to the correct

torque.

Содержание Rear Blades RBT4596







































Результаты поиска

Содержание Rear Blades RBT4596

Отзывы:

Похожие инструкции для Rear Blades RBT4596

Бренды по названию

Популярные бренды

Land Pride Rear Blades RBT4596, Руководство оператора

Результаты поиска

Содержание Rear Blades RBT4596

Отзывы:

Похожие инструкции для Rear Blades RBT4596

Бренды по названию

Популярные бренды