Land Pride Rear Blades RBT4596 Скачать руководство пользователя страница 16

Страница: 16 / 38

Section 1: Assembly & Set-Up

RBT4596 & RBT45108

Rear Blades 301-205M

1/13/21

Table of Contents

Blade Angling Cylinder

Refer to Figure 1-4:

WARNING

To avoid serious injury or death:
Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

1. Position hydraulic cylinder (#3) with ports on top as

shown. Install two 90 degree elbows (#4) into the

cylinder ports as shown. Tighten as needed.

2. Screw 74" long hydraulic hose (#6) into elbow (#4) at

the cylinder base and tighten.

3. Screw 82" long hydraulic hose (#5) into elbow (#4) at

the cylinder rod end and tighten.

4. Thread adapter fittings (#7) to the other end of the

hydraulic hoses and tighten.

5. Thread quick disconnect couplers (#8) to adapter

fittings (#7).

6. Attach hydraulic cylinder to the lugs on the right side

of the frame with clevis pins (#1). Make sure

hydraulic ports are positioned on top and the cylinder

base in positioned to the front as shown.

7. Secure clevis pins with hair pin cotters (#2).
8. Route hoses through hose bracket located on the

right side of the front hitch. Connect hoses to tractor's

hydraulic system.

Hydraulic Blade Angling

Figure 1-4

IMPORTANT:

Attach cylinder base to the front

cylinder mount. The base will interfere with the

mainframe if attached to rear cylinder mount.

24994

Blade Offset Cylinder

Refer to Figure 1-3:

WARNING

To avoid serious injury or death:
Do not remove shipping block from blade tilt housing until

after all manual links, ratchet jack, and/or hydraulic cylinders

have been installed and cylinders have been charged with oil.

Assemble hydraulic hoses to the hydraulic cylinder

before placing cylinder on the blade.
1. Position hydraulic cylinder (#3) with ports on top as

shown. Install two 90 degree elbows (#4) into the

cylinder ports as shown. Tighten as needed.

2. Screw 74" long hydraulic hose (#6) into elbow (#4) at

the cylinder base and tighten.

3. Screw 82" long hydraulic hose (#5) into elbow (#4)

located at the cylinder rod end and tighten.

4. Thread adapter fittings (#7) to the other end of the

hydraulic hoses and tighten.

5. Thread quick disconnect couplers (#8) to adapter

fittings (#7).

6. Attach hydraulic cylinder to lugs located on left side of

3-Way Rear Blade with clevis pins (#2). Make sure

hydraulic ports are positioned on top and the cylinder

base in positioned to the front as shown.

7. Secure clevis pins with hair pin cotters (#1).
8. Route hoses through hose bracket located on the

right side of the front hitch. Connect hoses to tractor's

hydraulic system.

Hydraulic Blade Offsetting

Figure 1-3

IMPORTANT:

Attach cylinder base to the front

cylinder mount. The base will interfere with the

mainframe if attached to rear cylinder mount.

24993

Содержание Rear Blades RBT4596







































Результаты поиска

Содержание Rear Blades RBT4596

Отзывы:

Похожие инструкции для Rear Blades RBT4596

Бренды по названию

Популярные бренды

Land Pride Rear Blades RBT4596, Руководство оператора

Результаты поиска

Содержание Rear Blades RBT4596

Отзывы:

Похожие инструкции для Rear Blades RBT4596

Бренды по названию

Популярные бренды