Land Pride RCF3010 Скачать руководство пользователя страница 21

Страница: 21 / 76

Section 1: Assembly & Set-Up

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

11/8/18

Make sure you have read and follow all Safety Alerts
and Important Notes above before continuing.

2. The RCF(M)3010 cutter is equipped with

Cat. II & III hitches. Make sure your tractor’s hitch is
compatible with the cutter’s hitch.

3. Remove lower linchpins (#5) and hitch pins (#1).

Remove upper hairpin cotter (#4), flat washer (#3),
hitch tube (#2), and clevis pin (#6).

4. Slowly back tractor to cutter while using tractor’s

3-point control lever to align lower 3-point arm holes
with clevis hitch pin holes.

5. Engage tractor park brake, shut tractor engine off,

and remove key before dismounting from tractor.

6. Attach lower 3-point arms to clevises with hitch

pins (#1). Secure hitch pins with linchpins (#5).

The upper center 3-point link can be attached to the
cutter in one of two locations depending on which
hitch category the tractor has.

a. Connect Cat. ll center 3-point link to the middle

hitch holes in upper hitch plates with clevis
pin (#6), flat washer (#3), and hairpin cotter (#4).
Hitch tube (#2) is not used and should be stored
with cutter for safe keeping.

b. Connect Cat. lll center 3-point link to the upper

hitch holes in upper hitch plates with clevis pin
(#6), hitch tube (#2), flat washer (#3), and hairpin
cotter (#4).

8. Adjust stabilizers on the tractor’s lower 3-point arms

to stop lateral float. Please consult your tractor’s
manual for adjusting instructions.

9. Manually adjust one of the lower 3-point lift arms up

or down to level the cutter from left to right. Detailed
leveling instructions are provided later. Refer to

“Deck Leveling & Height Adjustment”

on page 40.

10. Continue with

“Driveline Hook-up (3-Point)”

page 18.

RCF(M)3010 Hitch Hook-Up (3-Point)

Refer to Figure 1-10:

DANGER

To avoid serious injury or death:

•

A crushing hazard exists while hooking-up and unhooking

implement. Keep people and animals away while backing-
up to implement or pulling away from implement. Do not
operate hydraulic controls while a person or animal is
directly behind the power machine or near the implement.

•

All guards and shields must be installed and in good

working condition while operating the implement.

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near
the driveline. A person’s body and/or clothing can become
entangled in the driveline.

WARNING

To avoid serious injury or death:

Always shut tractor down using “Tractor Shutdown
Procedure” provided in this manual before dismounting
tractor.

The following hook-up instructions are for RCF(M)3010
cutters. See page 16 for

“RCF(M)3096 Hitch Hook-Up

(3-Point)”

IMPORTANT:

The tractor’s lower 3-point arms must

be stabilized to prevent side-to-side movement.
Most tractors have sway blocks or adjustable chains
for this purpose.

NOTE:

Land Pride’s Quick Hitch can be attached to

the tractor to provide quick and easy 3-point hook-
up and detachment. See your nearest Land Pride
dealer to purchase a Quick-Hitch.

3-Point Hook-up to RCF(M)3010

Figure 1-10

35064

37298

Содержание RCF3010













































































Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды

Land Pride RCF3010, Руководство оператора

Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды