Land Pride RCF3010 Скачать руководство пользователя страница 22

Страница: 22 / 76

Section 1: Assembly & Set-Up

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

11/8/18

Driveline Hook-up (3-Point)

DANGER

To avoid serious injury or death:

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near
the driveline. A person’s body and/or clothing can become
entangled in the driveline.

•

All guards and shields must be installed and in good

working condition while operating the implement.

•

Do not use a power take-off adapter. The adapter will

increase strain on the tractor’s power take-off shaft causing
possible damage to shaft and driveline. It will also defeat
the purpose of the tractor’s power take-off shield.

•

Make certain driveline yokes are securely fastened at each

end. A loose yoke can work free allowing the driveline to
rotate uncontrollably causing implement damage and
bodily injury or death to anyone nearby.

WARNING

To avoid serious injury or death:

•

Always shut tractor down using “Tractor Shutdown

Procedure” provided in this manual before dismounting
tractor.

•

Check driveline when lowering implement to make sure it

does not interfere with the tractor drawbar. If needed, shut
tractor off and move or remove drawbar to prevent driveline
damage.

IMPORTANT:

The drivelines must be lubricated

before putting them into service. Refer to

“Lubrication Points”

on page 61.

IMPORTANT:

An additional driveline may be

required if implement is attached to more than one
tractor or if a Quick Hitch is used.

IMPORTANT:

Drivelines with friction clutches must

go through a “run-in” prior to initial use and after long
periods of inactivity. For detailed instructions, see

“Driveline Slip-Clutch”

on page 56.

IMPORTANT:

before hooking-up the driveline before

hooking-up the driveline. Structural damage to the
tractor and cutter can occur if this check is not made.
Refer to

“Check Driveline Collapsible Length”

page 26.

Driveline Hook-up (RCF3010 Shown)

Figure 1-11

Refer to Figure 1-11:

The cutter driveline fastens to the tractor power take-off
shaft with pull collar coupler (#11).

If driveline collapsible length has not been checked,
go to

“Check Driveline Collapsible Length”

page 26. Otherwise, continue with step 2 below.

2. Park tractor and cutter on a level surface.

3. Shut tractor down before dismounting. Refer to

“Tractor Shutdown Procedure”

on page 11.

4. If tractor drawbar interferes with the driveline during

hook-up, move drawbar forward, to the side, or
remove.

5. Lift driveline off of driveline support (#10). Driveline

support will rotate up until secure against
A-frame as it is spring loaded.

6. Pull back on driveline pull collar (#11) and push

driveline yoke onto tractor power take-off shaft.
Release pull collar and continue to push driveline
yoke forward until pull collar locks in place.

Pull on both ends of driveline to make sure it is
secured to the tractor and gearbox shafts.

8. Continue with

“Hydraulic Hook-up Option (3-

Point)”

on page 19.

Содержание RCF3010













































































Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды

Land Pride RCF3010, Руководство оператора

Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды