Land Pride RCF3010 Скачать руководство пользователя страница 18

Страница: 18 / 76

Section 1: Assembly & Set-Up

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

11/8/18

35205

RCF3096 Model With 15" Tailwheel Assembly

35206

RCF3096 Model With 21" Tailwheel Assembly

RCF3096 3-Point Tailwheel Assembles

Figure 1-7

3. Insert tailwheel spindle (#6) into pivot tube on end of

tailwheel arm (#2).

4. Install 2 1/4" O.D. machine washers (#4) over each

tailwheel spindle (#6) and secure with 3/8" x 2 1/2"
roll pins (#7).

5. Tailwheel arms (#2) should be adjusted to customer

preference. When completed, they should be equal
distance from center line of hydraulic lift cylinder.

a. Loosen hex flange locknuts (#8) and adjust

tailwheel arms (#2) in or out to desired locations.

b. Tighten locknuts (#8) to the correct torque.

6. Continue with

“RCF(M)3096 Hitch Hook-Up (3-

Point)”

on page 16.

RCF3096 Tailwheel Assembly (3-Point)

These instructions apply only to 96" models with the
optional rear axle hydraulic lift. If hydraulics are not
included with your cutter, skip to

“RCF(M)3096 Hitch

Hook-Up (3-Point)”

There are several cylinder mounting lugs (#5) that
can be installed on axle (#1). Refer to

NOTES IN

BOLD

in Figure 1-7 to make sure your cutter is

equipped with the correct mounting lug and that the
notch in the lug is located on the axle properly. See
your nearest Land Pride dealer if it is not correct.

2. Install washers (#3) as follows:

RCF3096 With 15" Tailwheels

•

Install two 2 1/4" O.D. machine washers (#3) onto
each tailwheel spindle (#6).

RCF3096 With 21" Tailwheels

•

Install one special 4" O.D. harden washer (#3) onto
each tailwheel spindle (#6).

NOTE:

If preferred, rear guards may be assembled

before the tailwheels. See

“Assembly of Optional

Equipment”

on page 34 for rear guard instructions.

Содержание RCF3010













































































Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды

Land Pride RCF3010, Руководство оператора

Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды