Land Pride RCF3010 Скачать руководство пользователя страница 38

Страница: 38 / 76

Section 2: Assembly of Optional Equipment

Table of Contents

RCF3096, RCF3010, & RCFM3010 Rotary Cutters 326-566M

11/8/18

Chain Safety Guards (Optional)

DANGER

To avoid serious injury or death:

Rotary Cutters have the ability to discharge objects at high
speeds; therefore, the use of front and rear safety guards is
mandatory when cutting along roadways and in areas where
people may be present. Stop blade rotation if a bystander is in
or around the area.

WARNING

To avoid serious injury or death:

Keep all safety guards in place. Rotary Cutters have the
ability to discharge objects at high speeds. Use extreme
caution when cutting in areas where people may be present. It
is best to operate the cutter when no one is nearby. Stop blade
rotation if someone is in or around the area.

Front Chain Guards

Refer to Figure 2-2:

Locate Single or Double Chain Guards (#1 & #2) with
notched ends out and attach to the deck as shown
with 1/2"-13 x 1" GR5 carriage bolts (#3) and hex
whiz nuts (#4).

NOTE:

Do not tighten hardware until assemblies

are complete.

NOTE:

The two carriage bolts “A” are not used if CV

driveline option is included. See

“Constant Velocity

Driveline (Pull-Type)”

on page 31.

Front Chain Guard (RCF3096 Single Chain Shown)

Figure 2-2

35072

Notched End

2. Attach reflector bracket (#5) with 1/2"-13 x 1 1/2"

carriage bolts (#6) and hex whiz nuts (#3).

3. If Constant Velocity driveline is included, attach

bearing support to front chain guards using
steps 1 & 2 on page 31 for installation instructions.

4. Tighten hex whiz nuts (#4) to the correct torque.

Rear Chain Guard

Refer to Figure 2-1:

Install Single or Double Rear Chain Guard (#1) to the
deck rear with 1/2"-13 x 1" long carriage bolts (#2),
and 1/2" flange nuts (#3).

2. Tighten hex whiz nuts (#3) to the correct torque.

Rear Chain Guard (RCF3096 Double Chain Shown)

Figure 2-1

35051

Section 2: Assembly of Optional Equipment

Содержание RCF3010













































































Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды

Land Pride RCF3010, Руководство оператора

Результаты поиска

Содержание RCF3010

Отзывы:

Похожие инструкции для RCF3010

Бренды по названию

Популярные бренды