Land Pride RC4615 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 68

background image

Section 1: Assembly & Set-up

Table of Contents

8/22/23

RC4615 & RCM4615 Rotary Cutters 331-644M

27

Unhook Rotary Cutter

Figure 1-25

21. Remove connecting hitch pin or bolt as follows:

a.

For Standard Clevis Hitch, See

Figure 1-25:

Remove hairpin cotter (#2) and hitch pin (#1).

a.

For LP Performance Hitch, See

Figure 1-26:

Refer to Detail B:

Remove hairpin cotter (#2) and

hitch pin (#1).

b.

For Bar-Tite Hitch, See

Figure 1-27:

Remove locknut (#2) and bolt (#1).

22. Restart tractor and drive tractor slowly forward

several feet.

23. Shut tractor down properly before dismounting.

24. Lower park jack until cutter is resting on its front skid

shoes.

25. Replace connecting pin/bolt (#1) as follows:

a.

For Standard Clevis Hitch, See

Figure 1-25:

Insert hitch pin (#1) into clevis hitch as shown.
Secure hitch pin with hairpin cotter (#2).

b.

For LP Performance Hitch, See

Figure 1-26:

Refer to Detail A:

Rotate clevis (#9) horizontal

and flip hitch holder (#11) up so that its holes are
on top as shown. Insert customer-supplied hitch
pin (#1) through holes in hitch holder (#11).
Secure with hairpin cotter (#2).

c.

For Bar-Tite Hitch, See

Figure 1-27:

Remove hitch (#10) from tractor drawbar and
reattach it to cutter hitch (#9) with removed
bolt (#1) and locknut (#2) Screw locknut on 4 or 5
full turns. Do not torque nut tight.

37605

Unhook Tractor From LP Performance Hitch

Figure 1-26

Unhook Tractor From Bar-Tite Hitch

Figure 1-27

37631

33870

«
...
29
30
31
32
33
...
»

Содержание RC4615





































































Отзывы:

Нет отзывов

Похожие инструкции для RC4615

Бренд: Raymarine Страницы: 70

Бренд: Harbor Freight Tools Страницы: 4

Coronis 5MP Mammo

Бренд: Barco Страницы: 4

Бренд: Barco Страницы: 167

Color Coronis 2MP

Бренд: Barco Страницы: 156

Color Coronis 2MP

Бренд: Barco Страницы: 12

Бренд: Barco Страницы: 39

Бренд: Barco Страницы: 158

Бренд: ParaBody Страницы: 3

Бренд: Hach Страницы: 52

Бренд: hager Страницы: 2

Бренд: Qiagen Страницы: 48

Бренд: Qiagen Страницы: 162

Бренд: Qazqa Страницы: 4

Бренд: Qlightec Страницы: 12

Бренд: ZOLL Страницы: 48

Бренд: Vaisala Страницы: 2

Бренд: Tieline Страницы: 359

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды