Land Pride RC4615 Скачать руководство пользователя страница 57 | Manualshive

Страница: 57 / 68

background image

Section 5: Maintenance & Lubrication

Table of Contents

8/22/23

RC4615 & RCM4615 Rotary Cutters 331-644M

53

Gearbox

Method 1:

Unscrew top vented dipstick (#1). Wipe oil

from dipstick and screw dipstick in without tightening.
Unscrew dipstick and check oil on dipstick. If below
bottom level mark, add recommended gear lube through
dipstick hole until oil reaches top mark on dipstick.
Reinstall vented dipstick and tighten.

Method 2:

Remove side oil plug (#2). If oil is below

bottom of plug hole, add recommended gear lube
through top dipstick hole until oil flows out of side plug
hole. Reinstall and tighten side oil plug (#2) and vented
dipstick (#1).

Type of Lubrication: 80-90W EP Gear Lube

Quantity = Fill until oil reaches top mark on dipstick or
begins to flow out side plug hole in gearbox

.

IMPORTANT:

Do not overfill the gearbox with oil. Oil

will expand when hot. Make sure the implement is
level and oil is cool before checking oil level.

If oil has been removed from the gearbox, refill
gearbox to plug level or full mark on the dipstick.
Allow time for air to bleed up from the lower cavity,
and then recheck.

30215

Do Not Overfill

NOTE:

Use a suction or siphon pump to drain

gearbox of oil when there is not an oil drain plug.

8

Hours

23603

Divider Box

Method 1:

Unscrew top vented dipstick. Wipe oil from

dipstick and screw dipstick in without tightening. Unscrew
dipstick and check oil on dipstick. If below bottom level
mark, add recommended gear lube through dipstick hole
until oil reaches top mark on dipstick. Reinstall vented
dipstick and tighten.

Method 2:

Remove side oil level plug. If oil is below

bottom of plug hole, add recommended gear lube
through top oil fill/vended dipstick hole until oil flows out
of side oil level plug hole. Reinstall and tighten side oil
level plug and oil fill/vented dipstick.

Type of Lubrication: 80-90W EP

Quantity = Fill until oil begins to flow out oil level plug hole
in gearbox.

IMPORTANT:

Do not overfill the gearbox with oil. Oil

will expand when hot. Make sure the implement is
level and oil is cool before checking oil level.

If oil has been removed from the gearbox, refill
gearbox to plug level or full mark on the dipstick.
Allow time for air to bleed up from the lower cavity,
and then recheck.

8

Hours

«
...
55
56
57
58
59
...
»

Содержание RC4615





































































Отзывы:

Нет отзывов

Похожие инструкции для RC4615

Бренд: Odom Страницы: 19

Бренд: MacDon Страницы: 30

Бренд: Walker Bay Страницы: 8

Бренд: Labnet Страницы: 2

Бренд: Harken Страницы: 4

Бренд: GE Страницы: 24

Бренд: UNIA Страницы: 62

Бренд: R2 Страницы: 20

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: B. Braun Страницы: 2

Aesculap Neurosurgery

Бренд: B. Braun Страницы: 13

Aesculap AdTec mini

Бренд: B. Braun Страницы: 2

Бренд: B.Well Страницы: 2

Бренд: B. Braun Страницы: 55

BA Ultimate LED

Бренд: B.A. International Страницы: 234

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды