Land Pride RC4610 Скачать руководство пользователя

Страница: 29 / 68

Section 1: Assembly & Set-up

Table of Contents

RC4610 (540 RPM) and RCM4610 (1000 RPM): Rotary Cutters: 334-144M:

1/14/19

Purge Hydraulic System

DANGER

To avoid serious injury or death:

Never remove or install a folding wing cylinder with cylinder
rod retracted and wing folded up. The wing is unstable without
its folding cylinder and can suddenly fall. Also, air trapped in
a new or repaired cylinder will drop the wing suddenly when
lowering the wing. Either situation can render the cutter
inoperable and cause serious bodily injury or death.

WARNING

To avoid serious injury or death:

Be sure center and wing decks are lowered to the ground and
all hydraulic pressure is relieved before disconnecting any
hydraulic lines or fittings to purge the hydraulic system.

Wing Fold Cylinder

Refer to Figure 1-21:

Lower center deck until it is supported by stroke
control spacers (#5) on hydraulic cylinder (#3).

2. Lower wing deck until it is resting on the ground.

3. Shut tractor down properly and move wing control

levers back and forth to relieve all hydraulic pressure.
See

“Tractor Shutdown Procedure”

on page 16.

4. Slightly loosen hydraulic hose fitting (#2) at wing

cylinder (#1) to allow air to escape.

5. Restart tractor and slowly activate tractor control

lever to retract wing cylinder (#1), and to purge
trapped air from the hydraulic system.

6. Tighten hose fitting at the wing cylinder.

Deck Lift Cylinder

Refer to Figure 1-21:

Lower center deck until it is supported by stroke
control spacers (#5) on hydraulic cylinder (#4).

2. See

“Tractor Shutdown Procedure”

on page 16.

Shut tractor down properly and move deck lift control
lever back and forth to relieve all hydraulic pressure.

3. Slightly loosen hydraulic hose fitting (#4) at deck lift

cylinder (#3) to allow air to escape.

4. Restart tractor and slowly activate tractor control lift

lever to extend lift cylinder (#3) and to purge trapped
air from the hydraulic system.

5. Tighten hose fitting (#4) at lift cylinder (#3).

Purge Wing cylinders & Deck Lift Cylinder

Figure 1-21

39195

Содержание RC4610





































































Результаты поиска

Содержание RC4610

Отзывы:

Похожие инструкции для RC4610

Бренды по названию

Популярные бренды

Land Pride RC4610, Руководство оператора

Результаты поиска

Содержание RC4610

Отзывы:

Похожие инструкции для RC4610

Бренды по названию

Популярные бренды