Land Pride RC4610 Скачать руководство пользователя

Страница: 25 / 68

Section 1: Assembly & Set-up

Table of Contents

RC4610 (540 RPM) and RCM4610 (1000 RPM): Rotary Cutters: 334-144M:

1/14/19

Transport Bar, Locked Position

Figure 1-14

Unfold Wing

DANGER

To avoid serious injury or death:

Keep everyone out of the area where the wing deck will unfold.
The wing deck can fall suddenly.

Refer to Figure 1-14:

Park tractor and cutter on a level surface.

2. Raise wing up to release any tension on transport

lock bar (#3).

3. Shut tractor down properly before dismounting. Refer

“Tractor Shutdown Procedure”

on page 16.

4. Remove hairpin cotter (#1) from cylinder pin (#4).

Refer to Figure 1-15:

5. Rotate end of transport lock bar (#3) to the storage

pin (#2) as shown in Figure 3-2 on page 36. Secure
with hairpin cotter (#1).

6. Restart tractor and lower wing with tractor hydraulic

control lever until wing is on the ground.

27921

Transport Bar, Storage Position

Figure 1-15

27923

Содержание RC4610





































































Результаты поиска

Содержание RC4610

Отзывы:

Похожие инструкции для RC4610

Бренды по названию

Популярные бренды

Land Pride RC4610, Руководство оператора

Результаты поиска

Содержание RC4610

Отзывы:

Похожие инструкции для RC4610

Бренды по названию

Популярные бренды