Land Pride LR3784, Руководство оператора

Страница: 11 / 30

7
Section 1: Assembly & Set-up
2/26/16 LR3784 & LR3796 Landscape Rakes 302-337M
Table of Contents
Section 1: Assembly & Set-up
Landscape Rake Assembly
Figure 1-1
35096
Slot In Turn Table
Typical Both Sides
5. Clean excess grease and paint from around top of
pivot shaft (#7) and inside of pivot hole in main frame.
6. Rotate mainframe (#3) to the left to align Z-bracket
(#14) located beneath mainframe with slot in turn
table and lower rear hole in mainframe over pivot
shaft (#7).
7. Once mainframe is fully onto pivot shaft, rotate
mainframe until hole “A” in turntable is aligned with
hole “B” in mainframe. Make sure Z-bracket (#14)
under mainframe is positioned under turntable.
8. Attach drive pivot cap (#6) and pivot cap (#5) to pivot
shaft (#7) with 3/4"-10 x 1 1/2" GR5 hex flange
screw (#8). Tighten screw to the correct torque.
9. Insert 1" bent pin (#13) through holes “B” and “A”.
10. Rotate parking stand (#4) down and secure with wire
snap locking pin (#12). Make certain wire snap is
fastened over end of pin to retain pin.
!
CAUTION
Always check to make certain pivot retaining cap screw is in
place before making adjustments to the rake. If pivot retaining
cap screw is missing, the rake will fall off during adjustment.
11. Remove cotter pin (#11) and pivot shaft (#1) from
hitch frame (#2).
12. Align pivot holes in hitch frame (#2) with pivot tube in
mainframe (#3). Make sure Z-bracket (#15) under
mainframe is positioned under hitch turntable.
13. Attach hitch frame (#2) to mainframe (#3) with
front pivot shaft (#1). Secure pivot shaft with cotter
pin (#11). Bend one or both legs of the cotter pin to
keep the cotter pin from falling out.
14. Align hole “C” in hitch turntable with hitch pin hole “D”
and insert 1" bent pin (#13).
Tractor Requirements
!
WARNING
Ballast weights may be required to maintain steering control.
Refer to your tractor Operator’s Manual to determine proper
ballast requirements.
!
WARNING
Do not use tractors outside the rake’s rated horsepower range.
Under horsepower tractors cannot properly handle the rake.
Over horsepower tractors can damage the rake’s structure.
Tractor horsepower and hitch category should be within
the range noted below.
Horsepower Rating . . . . . . . . . . . . . . . . . . . 35-80 HP
3-point Hitch Category . . . . . . . . . . . . . . . . Cat. I or ll
Torque Requirements
See “Torque Values Chart” on page 24 to determine
correct torque values when tightening hardware.
Landscape Rake Assembly
Refer to Figure 1-1:
!
DANGER
Landscape Rake components can injure a person should they
suddenly fall. Always make certain components are properly
secured before lifting and properly supported on the ground
before removing lifting device. Always keep feet and other
extremities clear of areas where components can fall.
1. Elevate and Block up the rake frame so that the pivot
shaft (#7) sits vertical as shown.
2. Attach parking stand (#4) to mainframe (#3) with
3/8"-16 x 3" GR5 hex flange screw (#9) and hex
flange locknut (#10).
Draw locknut up snug, do not
tighten .
3. Rotate parking stand (#4) down and secure with wire
snap locking pin (#12). Make certain wire snap is
fastened over end of pin to retain pin.
4. Remove hex flange screw (#8), pivot cap (#5), and
drive pivot cap (#6) from pivot shaft (#7).
IMPORTANT: Remove paint from rake pivot shaft
and wipe grease from inside of mainframe pivot hole
before lowering mainframe onto blade pivot shaft.