background image

6

Installing CO

2

 Supply

1.  Connect high pressure CO

2

 regulator assembly to CO

2

     

cylinder or bulk system.

2.  Connect a 1/4” nut, stem and seal to CO

2

 regulator outlet.

3.  Route appropriate tubing from the low pressure CO

2

         

regulator manifold location to the 1/4” nut, stem on the high 

pressure CO

2

 regulator attached to source and connect 

tubing.

 

A dedicated CO

2

 regulator is required to supply the CO

2

 

inlet at the unit as well as to all syrup pumps. 

ATTENTION

4.  Connect tubing routed from the CO

2

 inlet at the unit to one of 

the low pressure CO

2

 regulator manifold outlets.

5.  Connect tubing routed from the tee at the syrup pumps to 

the second outlet of the low pressure CO

2

 regulator manifold. 

A

B

C

D

A. Line to Dispenser

B. Line to Syrup Pumps

C. Line to CO

2

 Regulator

D. CO

2

 Regulator Manifold

Remote Pump Installation

1.  If necessary, install water booster (Lancer PN MC-163172) 

between water supply and the unit.

2.  Using tubing cutters, cut water line and install tee fitting, then 

route appropriate tubing from the remote pump location to 

the tee fitting at water line. 

3.  Connect line from tee fitting at water line to the remote pump 

deck inlet regulator.

4.  Complete the carbonated water line connection, installed in 

the previous section, between the remote pump deck and 

carbonated water inlet on the unit.

5.  Install a shut-off valve in the water line feeding the deck. If a 

separate water line is run for plain water, ensure that it also 

has a shut-off valve.

A

A. Drain Fitting

B. Drain Line

C. Drip Tray

B

C

 

Pouring hot water down the drain may cause the Drain 

 

Tube to collapse. Allow only luke warm or cold water to 

 

enter the Drain Tube.

 

Pouring coffee, tea, or other 

 

similar substances down the drain may cause the Drain 

 

Tube to become clogged.

ATTENTION

A

B

C

D

A. Tee Fitting

B. Line to Plain Water Inlet

C. Line to Water Source

D. Line to Remote Pump

A

B

C

A. Oetiker Pliers           C. Pump Inlet

B. Line to Tee Fitting     D. Pump Outlet

D

 

Before installing regulator, assure that a seal (washer 

or o-ring) is present in regulator attachment nut.

ATTENTION

Thread regulator nut on to tank, then   

 

tighten nut with wrench

A. CO

2

 Regulator

B. Outlet

C. Wrench

D. CO

Supply

A

B

C

D

A. CO

2

 Regulator

B. 1/4” Nut, Stem & Seal

C. Line to CO

2

 Regulator  

     Manifold

D. Oetiker Pliers

A

B

C

D

Содержание Bevariety ACIB Series

















Отзывы: