Lambda Genesys GENH 750W, Техническое руководство

Страница: 5 / 79

83-507-013 Rev. A
TABLE OF CONTENTS
3.8.8 Address setting Pg. 18
3.8.9 Baud rate setting Pg. 18
3.9 CONNECTING THE LOAD Pg. 18
3.9.1 Load Wiring Pg. 18
3.9.2 Current Carrying Capacity Pg. 18
3.9.3 Wire termination Pg. 19
3.9.4 Noise and Impedance Effects Pg. 20
3.9.5 Inductive loads Pg. 20
3.9.6 Making the load connections Pg. 20
3.9.7 Connecting single loads, local sensing (default) Pg. 23
3.9.8 Connecting single loads, remote sensing Pg. 23
3.9.9 Connecting multiple loads, radial distribution method Pg. 23
3.9.10 Multiple loads connection with distribution terminals Pg. 24
3.9.11 Grounding outputs Pg. 24
3.10 LOCAL AND REMOTE SENSING Pg. 25
3.10.1 Sensing wiring Pg. 25
3.10.2 Local sensing Pg. 25
3.10.3 Remote sensing Pg. 26
3.10.4 J2 sense connector technical information Pg. 26
3.11 REPACKAGING FOR SHIPMENT Pg. 26
CHAPTER 4 FRONT AND REAR PANEL CONTROLS AND CONNECTORS Pg. 27
4.1 INTRODUCTION Pg. 27
4.2 FRONT PANELCONTROLS AND INDICATORS Pg. 27
4.3 REAR PANELCONNECTIONS AND CONTROLS Pg. 29
4.4 REAR PANEL SW1 SETUP SWITCH Pg. 30
4.4.1 SW1 positions functions Pg. 31
4.4.2 Resetting the switch Pg. 31
4.5 REAR PANEL J1 PROGRAMMING AND MONITORING CONNECTOR Pg. 32
4.5.1 Making J1 connections Pg. 32
CHAPTER 5 LOCAL OPERATION
Pg. 34
5.1 INTRODUCTION Pg. 34
5.2 STANDARD OPERATION Pg. 34
5.2.1 Constant Voltage Mode Pg. 34
5.2.2 Constant Current Operation Pg. 34
5.2.3 Automatic Crossover Pg. 35
5.3 OVER VOLTAGE PROTECTION (OVP) Pg. 35
5.3.1 Setting the OVP level Pg. 35
5.3.2 Activated OVP protection indications Pg. 35
5.3.3 Resetting the OVP circuit Pg. 35
5.4 UNDER VOLTAGE LIMIT Pg. 36
5.4.1 Setting the UVL level Pg. 36
5.5 FOLDBACK PROTECTION Pg. 36
5.5.1 Setting the Foldback protection Pg. 36
5.5.2 Resetting activated Foldback protection Pg. 36
5.6 OUTPUT ON/OFF CONTROL Pg. 36
5.7 OUTPUT SHUT-OFF (SO) CONTROL VIA REAR PANEL J1 CONNECTOR Pg. 36
5.8 ENABLE/DISABLE CONTROL VIA Pg. 37
5.9 CV/CC SIGNAL Pg. 37
5.10 PS OK SIGNAL Pg. 37
5.11 SAFE START AND AUTO-RESTART MODES Pg. 38
5.11.1 Automatic start mode Pg. 38
5.11.2 Safe start mode Pg. 38
5.12 OVER TEMPERATURE PROTECTION (OTP) Pg. 38
5.13 LAST SETTING MEMORY Pg. 38
5.14 SERIES OPERATION Pg. 38
5.14.1 Series connection for increased output voltage Pg. 39
5.14.2 Series connection for positive and negative output voltage Pg. 40
5.15 PARALLEL OPERATION Pg. 41