background image

 

         83-507-013 Rev. A                                                                                         

 

 

42 

• 

SW1 position 2 - Down in the Master Supply and up in all Slave Supplies. 

• 

Connect a short between J1-8 and J1-12 in all Slave Supplies. 

• 

Connect J1-25 of the Master Supply to J1-10 of all Slave Supplies. 

• 

Connect J1-16 of the Master Supply to J1-15 of the ‘First’ Slave Supply. 

• 

Connect J1-16 of the ‘First’ Slave Supply to J1-15 of the ‘Second’ Slave Supply (if any) 

• 

Connect J1-16 of the ‘Second’ Slave Supply to J1-15 of the ‘Third’ Slave Supply (if any) 

• 

Connect J1-16 of the ‘Last’ Slave Supply to J1-15 of the Master Supply 

• 

Connect J1-12 common to all supplies 

• 

Select Local or Remote sense - Ref. Figures 5-4 and 5-5 

2. Setting the units as Master or Slave 

a) Depress and hold the FINE button for 3 seconds. The Master/Slave configuration will be displayed on 
the Current Display. Rotate the CURRENT encoder to obtain the desired mode. Refer to Table 5-4 for 
the CURRENT display and modes of operation. 

CURRENT Display 

Operating Mode 

H1 

Single supply (default) 

H2 

Master supply with 1 Slave supply 

H3 

Master supply with 2 Slave supplies 

H4 

Master supply with 3 Slave supplies 

S Slave 

supply 

Table 5-4: Setting mode of operation 

b) When the desired configuration is obtained, depress and release the FINE button or wait approx. 5 
seconds. 

3. Master and Slave units default operation 

a) When a unit is programmed to Slave mode it enters the Remote mode with Local Lockout. In this 
mode, the front panel controls are disabled to prevent accidental setting change (refer to Sec. 7.2.7 for 
details). 
b) The Slave units parameters will automatically set the following: 
    *Output voltage to approximate. 102% of rated output voltage. 
    *Programmed Current to zero. 
    *UVL to zero volts 
    *OVP to its maximum value 
    *AST On 
    *OUT On 
    *Foldback protection Off 
c) The Master and Slave modes are stored in the power supply EEPROM when the AC power is turned off. 
The system will return to the Master/Slave mode upon re-application of AC power. 

4. CURRENT display accuracy 

In the advanced parallel mode, the Master unit calculates the total current by multiplying the Master output 
current by the number of Slave units. In this method, the CURRENT display accuracy is 2% +/- 1 count. In 
cases that higher accuracy is required, it is recommended to use the basic parallel operation mode. 

5.  To release units from Slave mode 

Slave units can be released using the following procedure: 
a) Depress FINE button for 3 seconds. The Master/Slave configuration will be displayed on the 
CURRENT display. 
b) Select H1 mode using the CURRENT encoder. 
c) Depress FINE button again or wait 5 seconds. 
d) Turn the AC power Off to store the new setting. 

e) After exiting from Slave operation the unit’s parameters will be set to: 

    

*Programmed Voltage to zero 

    

*Programmed Current to zero 

Содержание Genesys GENH 750W
















































































Отзывы: