background image

-4-

www.igmtools.com

Stay alert! Give your work undivided attention. Use common sense. Do 

not operate the machine under the influence of drugs, alcohol or any 

medication. 

Keep children and visitors a safe distance from the work area. Never 

leave a running machine unattended. Before you leave the workplace 

switch off the machine. 

Do not use the machine in a dump environment and do not expose it to 

rain. 

Focus on the position of your fingers and other parts of your body when 

working. Do not start the machine without safety appliances. 

Machine only stock which rests securely on the table. 

Do not remove chips and workpiece parts until the machine is at a 

standstill. 

Clamp the workpiece only when the machine is switched off. Rotate the 

workpiece by hand before starting the machine. Rough out the workpiece 

before installing it on the faceplate. 

Do not stand on the machine. 

Use a suitable power cord that can handle the machine‘s power input. 

Connection and repair work on the electrical installation may be carried 

out by a qualified electrician only. 

Have a damaged or worn power cord replaced immediately. 

Make all machine adjustments or maintenance with the machine 

unplugged from the power source. 

3.3 Hazards

When using the machine according to regulations some remaining 

hazards may still exist. 

Thrown workpieces and workpiece parts can lead to injury. 

Only process selected woods without defects. 

Dust and noise can be health hazards. 

Be sure to wear safety goggles, ear protection and dust mask. 

Do not use damaged or worn power cord. 

3.4 Grounding Instructions 

Connection cord: 

In case of a defect or malfunction, grounding provides a path of least 

resistance to electric current, reducing the risk of electric shock. The 

machine is supplied with connection cord with a guard wire and euro plug. 

The plug must only be connected to an appropriate outlet in accordance 

with all local codes and regulations. 

   • Do not modify the plug, if it does not fit into the socket. Contact a 

qualified electrician and have the appropriate socket installed. 

   • Improper connection may result in a risk of electric shock. Ground wire 

is an insulated wire with a green surface with/without yellow stripes. If the 

cord or plug needs to be repaired, contact a qualified electrician. 

   • Damaged cords should be repaired immediately and only by a 

qualified electrician. 

   • Use only three-wire cables with a euro plug and an appropriate socket. 

3.5 Woodturning Lathe 

Woodturning lathes are typically used to shape wood into cylindrical 

profiles. Objects made on a wood lathe include items such as furniture 

legs, lamp posts, baseball bats, bowls and other ornamental forms. Wood 

lathe tooling consists of fixturing and securing devices for the workpiece, 

a moveable toolrest and hand-held cutting tools in the form of long 

handled gouges, skews, scrapers and parting tools. Specialty tooling is 

also available for internal shaping and surface development. 

Electrical supply conditions - info for electricians 

Voltage: Steady state voltage: 0,9 to 1,1 of nominal voltage. 

Frequency: 0,99 to 1,01 of nominal frequency continuously; 0,98 to 1,02 

short time. 

Harmonics: Harmonic distortion not exceeding 10 % of the total r.m.s. 

voltage between live conductors for the sum of the 2nd through to 

the 5th harmonic. An additional 2 % of the total r.m.s voltage between 

live conductors for the sum of the 6th through to the 30th harmonic is 

permissible. 

Voltage unbalance: Neither the voltage of the negative sequence 

component nor the voltage of the zero sequence component in three-

phase supplies exceeding 2 % of the positive sequence component. 

Voltage interruption: Supply interrupted or at zero voltage for not more 

than 3ms at any random time in the supply cycle with more than 1s 

between successive interruptions. 

Voltage dips: Voltage dips not exceeding 20 % of the peak voltage of the 

supply for more than one cycle with more than 1s between successive 

dips. 

Physical environment and operating conditions 

Ambient air temperature: between 5° C to 40° C 

Humidity: The relative humidity does not exceed 50 % at a maximum 

temperature of 40° C. 

Altitude: Up to 1000 m MSL. 

Transportation and storage: Within a range of -25°C to 55° C and for short 

periods not exceeding 24 hours up to 70° C. 

Locking the lathe 

Fig. 1

Fig. 1: Method of locking Laguna Revo lathe. (1) Constructed 3 side 

box with padlock holes. (2) Padlocks. 

It is strongly recommended that the lathe is never left unattended in the 

unlocked condition. To lock the machine it is recommended that a cover 

(not supplied) is constructed.

4. Machine Specification 

Motor specification 

Power:                                                                      230V / 50 Hz / 1 phase 

Power output:                                                                             0,75 kW, S1 

  

 

 

 

                  (S1 - Permanent load) 

Current at maximum load 2,5 A 

Recommended circuit breaker                                                 16 A, tripping 

 

 

 

 

 

           rating C (16/1/C) 

Dimensions 

Package dimensions (LxWxH):  

920 mm x 380 mm x 520 mm

Package weight: 

61 kg

Length x width x height:  

750 mm x 226 mm x 442 mm 

Weight:                                                                                              56,3 kg 

Floor to bed height (no pads):                                                          170 mm 

Floor to Spindle Centre height (no pads):                                   328,75 mm 

Bed length:                                                                                    746,8 mm 

Toolrest length:                                                                              203,2 mm 

Toolrest post diameter:                                                                    25,4 mm 

Faceplate diameter:                                                                        76,2 mm 

Lathe Specification 

High Speed Range:  

 

 

           950 - 3500 RPM 

Mid Speed Range:    

 

 

           450 - 1750 RPM 

Low Speed Range:   

 

 

             100 - 525 RPM 

Distance between Centres:    

 

 

        390 mm 

Swing over Bed:    

 

 

 

        310 mm 

Swing over Banjo:    

 

 

 

        241 mm 

Spindle Bore:  

 

 

 

 

         9,5 mm 

Spindle / Tailstock Taper:  

 

 

 

   MK2 / MK2 

Spindle Thread:  

 

 

 

              M33 x 3,5 mm 

Содержание REVO 1216





















Отзывы: