Labwit ZWYC-290A Скачать руководство пользователя страница 49

Страница: 49 / 53

Ultimate-cell Stackable Shaking Incubator V2017.2

11. TROUBLE SHOOTING.

Error Indicator

Possible cause

Corrections

Power on, No display

Power supply is not connected

Check the power supply system to
see if there is voltage on the line

Plug has no access to socket

Plug in firmly

The power switch has not been
turned on.

Turn on the power switch on the side
cooling compartment of the unit

The fuse is broken

Replace fuse with new one of same
specification

Malfunction of the main power
board system

Notify distributor for repair service

Actual  temperature  is
higher  than  the  set
point,    high  tempera-
ture alarm is activated

Unit has not yet reached the
required (constant) tempera-
ture.

Wait a moment and observe

The circulation fan is broken

Notify the distributor to replace the
fan

Malfunction occurs with refrig-
eration system

Notify the distributor to repair the
refrigeration system

Actual temperature is
lower than the set
point.
low

temperature

alarm is activated

Unit has not yet reached the
required (constant) tempera-
ture

Wait a moment and observe

The circulation of cold air is
excessive

Close (part of) the ventilation open-
ing

The circulating fan is broken

Notify the distributor to replace the
fan

The heater does not work

Notify the distributor to repair the
heater

Actual temperature is
fluctuating and will not
be stable

The door (lid) is not closed
firmly

Close the door (lid) firmly

Malfunction occurs with the
control circuit

Notify distributor for repair service

Temperature

constant out of control

Malfunction occurs with the
control circuit

Notify distributor for repair service

The shaking move-
ment of platform is
unstable

The platform is in imbalance
due to a spoiled object

Remove the object , clear and clean
the chamber

The equipment is not placed
horizontally

Adjust the left-back foot leveler
install the equipment in a proper
way.

Malfunction occurs with control
circuit

Notify distributor for repair /service

The shaking platform
does not work

The door switch has not yet
made contact

Check the door to see if it is closed
firmly

The platform is blocked with an
object at the bottom

Remove the platform and clear the
object and clean the inside

The belt is broken

Notify the distributor to replace the
belt

Malfunction occurs with control
circuit

Notify distributor for repair service

The shaking move-
ment of platform is out
of control

Malfunction occurs with control
circuit

Notify distributor for repair service

Содержание ZWYC-290A






















































Результаты поиска

Содержание ZWYC-290A

Отзывы:

Labwit ZWYC-290A, Руководство пользователя, Страница: 49 / 53

Результаты поиска

Содержание ZWYC-290A

Отзывы: