Labwit ZWYC-290A Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 53

Labwit ZWYC-290A Скачать руководство пользователя страница 14

Ultimate-cell Stackable Shaking Incubator V2017.2

13



Remove the two caps on the door,



Use the Allen key (not supplied) to unscrew the 2 x M10 Hexagon screws



The door handle can now be removed.

5.3 Leveling the Units

5.3.1 Before starting your equipment, the unit must be placed horizontally on a solid,

flat floor, and elevated and leveled with three foot blocks and one flexible block
(with adjustable bolt). The foot blocks are provided to level as well as

“fix” the

unit firmly on the floor. To allocate the blocks in position, please do strictly
follow the below procedures:

5.3.2 Unscrew the safety nut on the flexible block first, screw down the adjusting bolt

of the flexible block, so that it will leave some gap when it fits underneath the
hole on the base.

5.3.3 There is one hole on each corner of base of the unit, locate each of them.

5.3.4 Use lifting tools to elevate the unit, and place the four foot blocks right un-

derneath the holes on each corner.

5.3.5 Lay down the unit, check and adjust the potions of the foot blocks and make

sure the tips of the blocks sits firmly in the holes. Make sure hands off the unit
before the unit is laid down! Do be careful of your hand!

5.3.6 Use a spanner to unscrew the adjusting bolt, raising the height of the flexible

block, until feeling some strength, and the tip of the bolt sits firmly in the hole.

5.3.7 Make sure the unit is elevated leveled and sits firmly on the four blocks. Try

setting the unit at its medium speed, e.g. 150rpm, slowly increase the speed
and adjust the adjusting bolt until no vibration is detected.

5.3.8 Finally screw the safety nut of the flexible block, lock up the adjusting bolt.

5.4 Preliminary Cleaning

Each new equipment was thoroughly cleaned prior to leaving the factory. It is recommended;
however, before installation, LABWIT recommends decontaminate all surfaces within the
interior chamber, outer door and gasket. They can be wiped down with a disinfectant of 70
percent alcohol or similar non-corrosive antimicrobial agent. After cleaning, dry all interior

Safety instruction!

Please be sure to follow the instructions, which are really im-

portant for your safety.

«
...
12
13
14
15
16
...
»

Содержание ZWYC-290A






















































Отзывы:

Нет отзывов