Labomed eVO 350 Скачать руководство пользователя страница 19

Страница: 19 / 20

eVO 350

8126300-795

eVO 350

Issue 1.2

Printed on June,2020

SPECIFICATIONS

Catalog Number

8126300-795

Physical Dimensions

Size:

Weight, unpacked: 23.0 lbs. (10.4 Kg)

Height: 19.8 in. (50.2 cm)

Weight, packed: 52 lbs (23.64 Kg)

Width: 10.5 in. (26.7 cm)
Depth: 14.0 in. (35.6 cm)

Electrical

voltage: 100-240 vAC
Power Input: Max 56-73vA
Frequency: 50/60 Hz
Fuses: T 1.6A L 250V
Halogen Bulb: (6V, 20 W), LED 5 Watt

Operational Conditions
Environmental

70°C

The environmental conditions are as follows:

Operating:

-20°C

Temperature: 10° C (50° F) to 35° C (95° F)
Relative Humidity: 30% to 75%

80%

Atmospheric Pressure: 80 kPa (23.6 in. Hg) to

106 kPa (31.3 in. Hg)

10%

Transportation & Storage:

Temperature -20° C (-4° F) to +70° C (158° F).

106 kPa

kPa Relative Humidity: 10% to 80% (non-condensing)

Atmospheric Pressure: 50 kPa (14.8 in. Hg) to

50 kPa

106 kPa (31.3 in. Hg)

Exposure to extreme temperature conditions indicated above must not exceed 15 weeks.

Optics

Microscope

Galilean

Mag Change

5 Step Drum Rotation

Eyepiece

12.5X

Mag Ratio

6.5X, 10X, 16X, 25X, 40X

IPD Range

48.5 - 77 mm

Diopter Adjustment

+/- 5

Slit Illumination

6v 20W Halogen/ 5W LED

Slit Width

0 – 13.5 mm

Slit Length

Slit Apertures

0.6, 5.8, 9, 13.5 mm and continuous 1.5 to 12.0 mm

Slit Rotation

0° - 180°

Filters

Red Free, Heat Absorbing, Cobalt Blue

Содержание eVO 350





















Результаты поиска

Содержание eVO 350

Отзывы:

Похожие инструкции для eVO 350

Бренды по названию

Популярные бренды

Labomed eVO 350, Руководство пользователя

Результаты поиска

Содержание eVO 350

Отзывы:

Похожие инструкции для eVO 350

Бренды по названию

Популярные бренды