Labomed eVO 350 Скачать руководство пользователя страница 17

Страница: 17 / 20

eVO 350

Figure 31 Changing
Target Light LED

Figure 31a Changing
Target Light LED

LED Cap

Pull LED Bulb

8126300-795

eVO 350

Issue 1.2

Printed on June,2020

FUSE REPLACEMENT

Replace the fuses in the Power Input Module with the
fuses indicated in the

Specifications

section of this manual.

1. Remove input power to the instrument.

2. Press down on the top tab in the middle of the
Power Input Module to release the Fuse Holder,
and gently pull out the Fuse Holder by gripping the
two small tabs. Refer to figures-29 & 30

3. Open the Door to the Fuse Holder by pulling
it down. Refer to figure-30.

NOTE:

The Fuses will pop up when the door is open,

making removal easier.

4. Install new fuses into the Fuse Holder that is
indicated in the Specification section of this manual.

5. Install the Fuse Holder by closing the door, and
pushing the Fuse Holder back until it snaps into place.

Replacement of Chin Rest Light Indicator

1. Unscrew the LED cap refer fig. 31.

2. Pull out the defective LED and replace with new LED.
refer fig.31a. Thread in the LED cap back.

NOTE:

If New LED does not light up after switching on.

remove it and re-fix after changing its polarity.

Pull

Out

Tabs

Figure-29 Pull Out

Open

Door

Figure-30 Open Fuse Door

Notch

Cut Out

Figure-28 Notches

Содержание eVO 350





















Результаты поиска

Содержание eVO 350

Отзывы:

Похожие инструкции для eVO 350

Бренды по названию

Популярные бренды

Labomed eVO 350, Руководство пользователя

Результаты поиска

Содержание eVO 350

Отзывы:

Похожие инструкции для eVO 350

Бренды по названию

Популярные бренды