Labconco Purifier 3970200 Скачать руководство пользователя | Manualshive

Страница: 35 / 65

background image

31

Chapter 6: Maintaining Your Vertical Clean Bench

Product Service 1-800-522-7658

4.

Using the “^” or “

ν

” keypads, respectively, increase or

decrease the numerical value until it equals 30 (2'), 20 (3'). 15
(4') for the Purifier Vertical Clean Bench enclosure at 55 fpm
downflow velocity.

5.

Press the “ENTER” Keypad. The photometer will scan for 15
seconds, and then the “0” keypad will flash. Press the “Enter”
keypad. The unit will scan for 5 seconds, the display will read
“0000,” and the unit will sound a confirming tone.

6.

Set the valve to “DOWNSTREAM.” Place the palm of your
hand over the sampling port of the pistol. There should be a
strong vacuum at this port. If the vacuum is weak, contact Air
Techniques Hamilton Associates.

7.

Turn the enclosure on and let it operate for a minimum of 5
minutes.

8.

If necessary, adjust the speed control of the enclosure to
maintain the following downflow airflows at 55 fpm; 2'
(230cfm), 3' (340 cfm), 4' (460 cfm.)

9.

Position the aerosol generator discharge in the intake of the
prefilter on top of the enclosure.

10.

Start the aerosol generator (Pressure to be 10 +/- 1 PSIG).
Ensure that one Laskin nozzle is in the “open” position.

11.

Allow the generator to operate for a minimum of 15 seconds.
Scan the downstream exhaust side of the HEPA filter by
passing the sampling nozzle of the gun in slightly overlapping
strokes over the entire surface the filter, with the sampling port
not more than 1 inch from the surface of the filter media. Scan
the entire periphery of the filter and the gasket between the
filter frame and the enclosure frame. Scanning shall be done at
a traverse rate of not more than 2 inches per second.

Acceptance

Aerosol penetration shall not exceed 0.01 percent measured by the
photometer.

«
...
33
34
35
36
37
...
»

Содержание Purifier 3970200


































































Отзывы:

Нет отзывов

Похожие инструкции для Purifier 3970200

Бренд: TDW Страницы: 20

TotalStorage FAStT EXP700

Бренд: IBM Страницы: 158

Бренд: PPM Страницы: 20

Бренд: StarTech.com Страницы: 13

Бренд: TOOQ Страницы: 22

Бренд: TOOQ Страницы: 26

Бренд: TOOQ Страницы: 30

Бренд: TOOQ Страницы: 22

Бренд: peerless-AV Страницы: 16

nrgSMART IOE-24S-A203

Бренд: Telect Страницы: 82

Бренд: Tranberg Страницы: 8

Бренд: Zaber Technologies Inc. Страницы: 39

Бренд: 3M Страницы: 12

Бренд: Macpower & Tytech Страницы: 38

Бренд: QNAP Страницы: 52

Бренд: Vantec Страницы: 2

Бренд: Icy Dock Страницы: 9

Бренд: Icy Box Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды