26
EN
cycles of approximately 10 seconds each; with a
3-second pause between cycles.
3. Push-button panel LED illumination
Switch off the machine using the main switch (
1
).
To turn on the LEDs, press and hold the button
(
17
) + the button (
6
); switch on the machine using
the button (
1
); after 5 seconds, buttons 6 and 17
light up and LED ON appears on the display (
10
);
confirm using the button (
18
).
To turn off the LEDs, press and hold the button
(
17
) + the button (
16
); switch on the machine using
the button (
6
); after 5 seconds, buttons (
16
) and
(
17
) light up and LED OFF appears on the display
(
10
); confirm using the button (
18
).
4. Pre-infusion ON/OFF
Switch off the machine using the main switch (
1
).
To activate pre-infusion, press and hold the
button (
6
); switch on the machine using the
button (
1
); after 5 seconds the button 6 lights up
and PRE ON appears on the display (
10
); confirm
using the button (
18
).
To deactivate pre-infusion, press and hold the
button (
16
); switch on the machine using the
button (
6
); after 5 seconds, the button (
16
) lights
up and PRE OFF appears on the display (
10
);
confirm using the button (
18
).
5. Deactivating pre-infusion on buttons 18 and 26
Switch off the machine using the main switch (
1
).
The programming is set for the dosage of buttons
(
6
) - (
16
) - (
18
) - (
26
). To switch off pre-infusion just
for buttons (
18
) and (
26
), press button (
6
) + button
(
16
); switch off the machine using the main switch
(
1
); after 5 seconds the buttons (
6
) and (
16
) light
up and P34 ON or OFF appears on the display (
10
);
confirm using the button (
18
).
6. Units of measure (C ° / F) and boiler
temperature
Switch to IDLE-OFF mode by pressing and
holding the button (
17
) and then the button (
18
)
immediately afterwards.
Press the button (
17
) for at least 5 sec. until F01
(units of measure) appears on the display; confirm
using the button (
17
).
Pressing buttons (
6
) and (
16
) selects the unit of
measure C° or F; confirm using the button (
17
).
Press the button (
17
) until F02 appears on the
display; confirm using the button (
17
).
Use buttons (
6
) and (
16
) (+ / -) to modify the
temperature value; confirm using the button (
17
).
Go back to IDLE ON mode by pressing and
holding the button (
17
) and then the button (
18
)
immediately afterwards.
7. Resetting factory settings
Switch to IDLE-OFF mode by pressing and
holding the button (
17
) and then the button (
18
)
immediately afterwards.
Press and hold buttons (
6
) + (
17
) + (
18
); after 5
seconds the buttons (
6
) - (
17
) - (
18
) light up and
PRS appears on the display (
10
).
10. DISPENSING COFFEE
To dispense coffee, press the selected group
head control button. Only the LED of the selected
dose will remain lit and coffee will start to be
dispensed. It will stop automatically when the
previously programmed amount is dispensed.
When the coffee has been dispensed, all the LEDs
on the push-button panel will light up.
Delivery can be interrupted or the selection
cancelled by pressing any of the group head
control buttons.
In addition to interrupting delivery and cancelling
the selection, the button (
17
) also has a
continuous delivery function. This means that
the dose is not pre-set and that the group head
will continue to deliver coffee until the button is
pressed again, which stops delivery.
If the coffee is too finely ground or too much
coffee has been placed in the filter, when you
press one of the four coffee control selectors,
coffee will not be dispensed. After 10 seconds,
the LED of the dose selected will start to flash and
alarm AL3 will be displayed. A flashing triangle
appears on the display; to view the alarm you
have to go to the alarm display screen.
To restart the machine, remove the filter-holder
and replace the coffee in the filter basket. Press
the main switch (
1
) to switch off the machine and
then restart it.
We recommend that you dispense steam
for a maximum of 60 seconds.
To prevent the machine from blocking,
if coffee does not start to be dispensed
within 10 seconds, press one of the
selector buttons to cancel the command,
replace the coffee in the filter and repeat
the dispensing procedure.
Содержание desiderio 3v
Страница 2: ...A B C D E F G DESIDERIO V GENIALE V GENIALE M 2 3 4 A B 1...
Страница 3: ...A B C D E F G DESIDERIO V GENIALE V GENIALE M 2 3 4 A B 1...
Страница 5: ......
Страница 6: ......