L3 Aviation Products Lynx NGT-9000+ Скачать руководство пользователя

Страница: 69 / 96

Lynx

NGT-9000

Pilot’s Guide

3-1

Controls and Indicators

CHAPTER 3

CONTROLS AND INDICATORS

INTRODUCTION

This chapter describes the controls, indicators, and other devices

that could be interfaced to the panel and remote mounted Lynx NGT-

9000.

COCkPIT SwITCHES

Cockpit switches are optional and may not be a part of the aircraft
installation.

IDENT

This switch activates SPI and transmits an ident pulse. An ident pulse

highlights the aircraft’s symbol on the ATC’s radar screen and is

identified on the Lynx NGT-9000 screen when active.

INDICATOR LAMPS

Indicator lamps are optional and may not be a part of the aircraft
installation.

TAS Alert

The TAS Alert lamp (amber) will illuminate when:

TAS is enabled and there is a Traffic Alert condition (only possible

when TAS is activated).
TAS is enabled and Self-test is run, the lamp will be “ON” for
approximately 8-10 seconds.

ADS-B Out Fail

The ADS-B Out Fail lamp primarily indicates when the Lynx NGT-9000

is not providing ADS-B output data. The lamp may be illuminated (ON)

for any of the following reasons:

When Lynx NGT-9000 is not powered, lamp defaults to “ON”.
When the aircraft is On-Ground and the self-test is run, the lamp

is “ON” for approximately. 8-10 seconds.
Aircraft On-Ground startup the lamp is “ON” initially until the Lynx

NGT-9000 has started and is operational after which the lamp will

extinguish.

•

1.
2.

Содержание Lynx NGT-9000+

































































































Результаты поиска

Содержание Lynx NGT-9000+

Отзывы:

Похожие инструкции для Lynx NGT-9000+

Бренды по названию

Популярные бренды

L3 Aviation Products Lynx NGT-9000+, Руководство пилота

Результаты поиска

Содержание Lynx NGT-9000+

Отзывы:

Похожие инструкции для Lynx NGT-9000+

Бренды по названию

Популярные бренды