L3 Aviation Products Lynx NGT-9000+ Скачать руководство пользователя

Страница: 44 / 96

Lynx

NGT-9000

Pilot’s Guide

2-18

Operation

TFC Button

The Traffic (TFC) button replaces the Altitude Mode button when the

status of the aircraft is On-Ground. The button also activates TAS

(optional) when the aircraft is On-Ground. A description of each mode

is detailed below:

Ground (GND): The display shows ground traffic only and places

TAS (if installed) in Standby. Standby indication is shown on the

Traffic Mode Indicator.

Air (AIR): The display shows air traffic only and activates TAS (if

installed).

All (ALL): The display shows air and ground traffic and activates

TAS (if installed).

Note

When no heading source is available and when going

through low speed operations (< 7 knots), ADS-B tracks

are removed because ownship track can not be adequately

determined. If TAS is not active, a “Traffic Unavailable”

message is displayed.

Transponder Banner

When the traffic application is displayed on the left screen, the

transponder banner is displayed at the top of the left screen with the

following information:

Quick return button is labeled “XPDR” and is used to return to the

Transponder Application screen
Mode A squawk code
Reply “R” or Ident “ID” indicator shown to the right of the squawk

code when either function is active.
Current transponder operating mode status indicator with green

text. An amber “XPDR Failed” is shown when the transponder

function has failed.

MSG Button

The MSG Button seen on the Traffic Screen has the same functionality

as the one shown on the Transponder screen. See page 2-10 for

details.

•

•
•

•

Содержание Lynx NGT-9000+

































































































Результаты поиска

Содержание Lynx NGT-9000+

Отзывы:

Похожие инструкции для Lynx NGT-9000+

Бренды по названию

Популярные бренды

L3 Aviation Products Lynx NGT-9000+, Руководство пилота

Результаты поиска

Содержание Lynx NGT-9000+

Отзывы:

Похожие инструкции для Lynx NGT-9000+

Бренды по названию

Популярные бренды