background image

Lynx 

® 

NGT-9000

Pilot’s Guide

1-8

Description

Traffic Information Service - Broadcast (TIS-B)

TIS-B is the broadcast from Ground Radio Stations of ATC-derived 

traffic information to ADS-B equipped aircraft.

The actual availability of services depends upon the availability of 

ground-based radar to support TIS-B source data.
Receiving aircraft must be in both ATC radar coverage and ground 

based  transceiver  (GBT)  coverage  in  a  given  area  to  receive 

TIS-B service in that area. When ownship is above 24,000 ft, the 

ground station will no longer provide TIS-B service. (Targets will be 

provided up to 27,500 ft) 
Other aircraft are provided by the ground station if within a 15nm 

horizontal range and +/-3,500 ft of altitude of the receiving aircraft. 

ADS-B equipped ground aircraft and vehicles are not displayed to 

airborne aircraft.
Aircraft not equipped with a transponder, or equipped with a Mode 

A only transponder are not part of the TIS-B data and will not be 

seen on the traffic display. 
The ground station will not provide display information for Mode 

C and Mode S transponder equipped aircraft that do not provide 

altitude information.
An aircraft on the ground receiving TIS-B is provided both ground 

aircraft and vehicles as well as airborne other aircraft within 5nm 

and 2,000 ft above ground level of the airport reference point. 
The TIS-B service is intended to improve the pilot’s ability to visually 

see traffic in the air and on the airport surface so that pilots can 

more effectively apply traditional “see-and-avoid” techniques.
TIS-B is NOT intended to be used as a collision avoidance system 

and does NOT relieve the pilot of responsibility to “see-and-avoid” 

other aircraft.
No avoidance  maneuvers  are provided  for, nor authorized, as a 

direct result of a TIS-B other aircraft being displayed in the cockpit. 

Avoidance  maneuvers  must  be  based  on  visually  acquiring  the 

target.

Содержание Lynx NGT-9000+

































































































Отзывы: