manualshive.com logo in svg

L-Card E20-10, Руководство пользователя

Поделиться
Скачать
L-Card E20-10 Скачать руководство пользователя страница 19

 

 

Firmware 

version 

Firmware description 

1.00.06 

dd. 15.01.07. 

Final firmware 

E20-10

 rev.

А

. 

2.00.03 

dd. 10.04.08. 

First firmware of serial 

E20-10

 

rev.В. 

 

Users applying internal calibration in  

E20-10

 

rev.В are recommended to update firmware 

to elder version where the effect to damage individual data samples in code approximating 
to ADC word size edge has been eliminated. Negative effects have not been found when 
internal calibration is off. 

2.00.05 

dd. 24.07.08. 

Updated firmware of serial 

E20-10

 

rev.В.

 

In FPGA 2.00.05 firmware the additional program start is not required under 
additional startup condition  "on

 signal passing through given level in selected channel" 

and shutdown condition "on number of M recorded frames", due completing of the next 
shutdown condition fulfillment the additional data acquisition start will begin 
automatically upon completing of new start condition fulfillment.    For another start 
conditions 

FPGA 2.00.05 firmware is similar to  2.00.03 firmware. Also refer to 

table 5-5

 notes to it. 

FPGA 2.00.03 and 2.00.05 firmwares are fully compatible on program library functions.  

2.00.06 

dd. 01.09.08г.

 

Updated firmware of serial 

E20-10

 

rev.В.

 

One-channel mode sensitive data acquisition fault has been eliminated

.

 

1.00.07 

dd. 29.10.08. 

Updated firmware of serial 

E20-10

 rev.A. 

Data corruption in repetitive interleaving of external start and program shutdown has been 
eliminated (this relates to rev.A only). FPGA 1.00.07 firmware means simultaneous 
upgrading of AVR controller firmware.  

2.00.07 

dd. 05.09.12. 

For E20-

10 rev.В the

 embedded software upgrading enabling to boost 

maximum possible 

frame size up to 8192 samples of

 

ADC

 has been developed!  To upgrade it is required to 

alter AVR controller and upgrade library remotely (FPGA 2.00.07 firmware has been yet 
added in which). Compatibility with old software of upper level is existed. 

2.00.08 

dd. 20.11.12. 

Firmware for E20-

10 rev.В. In comparison with version 2.00.07, the fault on odd data 

interference in ADC buffer in additional data acquisition starting on signal START under 
data acquisition program shutdown mode has been eliminated.   

2.00.10 

dd. 15.12.14. 

Firmware for E20-

10 rev.В. Data acquisition restart on signal START fault has been 

eliminated.   

 

Содержание E20-10




































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды