L-Acoustics X12 Скачать руководство пользователя страница 43

Страница: 43 / 100

Inspection and preventive maintenance

Depending on the displayed results, follow the instructions in the table.

result

interpretation

instructions

measured impedance is within expected range

enclosure is in working order electrically

unsupported preset family

only supported enclosures should be tested

Not Connected

if cables are connected:

inspect the cables and connections

go to step

(p.43)

NOK

measured impedance is not within expected range

UNDEF

measured impedance is undened

check that all the prerequisites are met, in

particular that the loaded preset corresponds

to the connected speaker's family

inspect the cables and connections

go to step

(p.43)

Under NC, NOK and UNDEF results, press and hold the corresponding OUT key.
The amplied controller displays:

• the tested frequencies,
• information on the measured impedance:

• OPEN for open circuit (found in NC results),
• SHORT for short circuit (found in NOK results), or
• a percentage of variation from the expected range (found in NOK and UNDEF results)

• the number of operational transducers out of the total

Low variations from the expected range are acceptable: displayed percentage can be different from 0 and all

transducers considered operational.

X12 owner's manual (EN) version 1.0

Содержание X12





































































































Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды

L-Acoustics X12, Руководство пользователя

Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды