L-Acoustics X12 Скачать руководство пользователя страница 30

Страница: 30 / 100

Loudspeaker congurations

X12 stage monitor

Deployed as a stage monitor, an X12 system operates over the nominal bandwidth of the X12 enclosure.
The [X12_MO] preset allows for a reference frequency response in stage monitoring applications.
The X12 enclosure is driven by LA4X / LA8 / LA12X.

Standalone X12

55°

35°

Enclosure X12

Preset [X12_MO]

Frequency range (-10 dB) 57 Hz - 20 kHz

Low-latency preset

A low-latency preset is available for the X12 system enclosure used as a monitor ([X12_MO]). It reduces latency from

3.84 ms down to 1.18 ms (LA8) and 0.84 ms (LA4X / LA12X). If the monitor is combined with a subwoofer, a custom

preset must be used.

Paired X12 system monitors with LFC

The Low Frequency Contour (LFC) tool implemented in LA Network Manager can compensate for coupling effects

between closely operating monitors. LFC allows to adjust the frequency response curve to obtain the desired low

frequency contour.
For paired X12 system monitors, enter the following parameters to obtain the reference response curve of a single

enclosure:

-3.0

180

For more information about LFC, refer to the

LA Network Manager Help

(section: Group Control Panel) and to the

Array Morphing

white paper, available on

www.l-acoustics.com

(Download Center).

X12 owner's manual (EN) version 1.0

Содержание X12





































































































Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды

L-Acoustics X12, Руководство пользователя

Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды