L-Acoustics X12 Скачать руководство пользователя страница 34

Страница: 34 / 100

Inspection and preventive maintenance

Inspection and preventive maintenance

How to do preventive maintenance

Inspect the system before any deployment and after any corrective maintenance operation.
Perform preventive maintenance at least once a year.
Refer to the maintenance manuals for advanced maintenance.

Rigging and hardware

Perform the

Rigging part inspection

(p.35) on each rigging part.

Use the

Mechanical system overview

(p.35) to identify critical parts of the system and apply the specic checks

described in the

Inspection references

(p.40).

If any parts are damaged, contact your L-Acoustics representative for further instructions.

Acoustics

Perform the

Enclosure check

(p.42).

Perform the

Listening test

(p.44) to detect any degradation in sound quality.

If necessary, refer to the

Corrective maintenance

(p.74) section for speaker repair kits and maintenance instructions.

X12 owner's manual (EN) version 1.0

Содержание X12





































































































Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды

L-Acoustics X12, Руководство пользователя

Результаты поиска

Содержание X12

Отзывы:

Похожие инструкции для X12

Бренды по названию

Популярные бренды