L-Acoustics KIVA II Скачать руководство пользователя страница 73

Страница: 73 / 148

Rigging procedures

Stacking

Stacking Kiva II on SB15m

type of deployment

stacking

rigging accessory

KIBU-SB

min number of operators

Additional safety

Secure the stack with straps.

Risk of falling objects

Verify that no unattached items remain on the array.

Cardioid conguration

A cardioid conguration is an array of four subwoofers with one reversed element.
Refer to the subwoofer user manual and to the

Cardioid congurations

technical bulletin for details about the

use of this conguration.
Any of the following subwoofer arrays can be set in cardioid conguration.

Assembly

About this task

To ground-stack Kiva II on KIBU-SB, start at step

(p.74).

Procedure

Prepare a stack of SB15m.
Secure the coupling bars with the locking tabs.

CLICK !

Make sure the safety label on each locking tab is fully covered.
Make sure the lugs are in the notches.

Secure KIBU-SB on top of the SB15m stack.
Use the KIBU-SB coupling bars.

Kiva II owner's manual (EN) version 1.0

Содержание KIVA II





















































































































































Результаты поиска

Содержание KIVA II

Отзывы:

Бренды по названию

Популярные бренды

L-Acoustics KIVA II, Руководство пользователя

Результаты поиска

Содержание KIVA II

Отзывы:

Бренды по названию

Популярные бренды