Kyocera Copystar CS-1635 Скачать руководство пользователя страница 121

Страница: 121 / 244

2HA/2HB

1-4-25

(15) Image is partly missing.

(16) Fuser is poor.

(17) Image is out of focus.

(18) Image center does not align with the original center.

Copy example

Causes

Check procedures/corrective measures

Paper damp.

Check the paper storage conditions.

Paper creased.

Replace the paper.

Dirty or flawed drum.

Clean the drum or, if it is flawed, replace the drum unit (see
page 1-5-23).

Dirty transfer roller.

Clean the transfer roller.

Copy example

Causes

Check procedures/corrective measures

Wrong paper.

Check if the paper meets specifications.

Defective pressure springs.

Replace the pressure springs.

Flawed press roller.

Replace the press roller (see page 1-5-30).

Defective fuser heater.

Replace the fuser heater (see page 1-5-31).

Copy example

Causes

Check procedures/corrective measures

Defective image scanning unit.

Replace the image scanning unit (see page 1-5-18).

Drum condensation.

Clean the drum.

Copy example

Causes

Check procedures/corrective measures

Misadjusted center line of image print-
ing.

Readjust the center line of image printing (see page 1-3-12).

Misadjusted scanner center line.

Readjust the scanner center line (see page 1-3-20).

Original placed incorrectly.

Place the original correctly.

Содержание Copystar CS-1635





















































































































































































































































Результаты поиска

Содержание Copystar CS-1635

Отзывы:

Похожие инструкции для Copystar CS-1635

Бренды по названию

Популярные бренды

Kyocera Copystar CS-1635, Руководство по обслуживанию

Результаты поиска

Содержание Copystar CS-1635

Отзывы:

Похожие инструкции для Copystar CS-1635

Бренды по названию

Популярные бренды