Kyocera Copystar CS-1635 Скачать руководство пользователя страница 52

Страница: 52 / 244

2HA/2HB

1-3-20

U067

Adjusting the scanner center line
Description

Adjusts the scanner center line of the original scanning.

Purpose

Make the adjustment if there is a regular error between the center lines of the copy image and original.

Caution

Before making this adjustment, ensure that the following adjustments have been made in maintenance mode

Adjustment

1. Press the start key.

2. Press the interrupt key.
3. Place an original and press the start key to make a test copy.
4. Change the setting value using the zoom +/- keys.

For copy example 1, increase the value. For copy example 2, decrease the value.

Figure 1-3-9

5. Press the start key. The value is set.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

U068

Adjusting the scanning position for originals from the DP
Description

Adjusts the position for scanning originals from the DP.

Purpose

Used when there is a regular error between the leading edges of the original and the copy image when the DP
is used.

Method

Press the start key.

Setting

1. Change the setting using the zoom +/- keys.

Increasing the value moves the image backward, and decreasing it moves the image forward.

Supplement

While this maintenance item is being executed, test copying from an original is available.

Completion

Press the stop/clear key. The indication for selecting a maintenance item No. appears.

Maintenance

item No.

Description

U067

U034

(P.1-3-12)

U072

(P.1-3-23)

Description

Setting range

Initial setting

Scanner center line

-66 to 66

-4

Original

Copy

example 1

Copy

example 2

Scanner center line

Description

Setting range

Initial setting

Change in value per step

Scanning position

-17 to 17

0.254 mm

Содержание Copystar CS-1635





















































































































































































































































Результаты поиска

Содержание Copystar CS-1635

Отзывы:

Похожие инструкции для Copystar CS-1635

Бренды по названию

Популярные бренды

Kyocera Copystar CS-1635, Руководство по обслуживанию

Результаты поиска

Содержание Copystar CS-1635

Отзывы:

Похожие инструкции для Copystar CS-1635

Бренды по названию

Популярные бренды