KYLAND Technology KGW3101 Скачать руководство пользователя | Manualshive

Страница: 34 / 42

background image

30

B. PC Configuration

Connect PC and the gateway serial port (S1) by DB9 female cable to configure for PC. Run

“Modbus Poll”

software on PC. The

“Modbus Poll” parameters must be configured as shown in the following figure.

Connection: Serial Port

Mode: RTU

Port: 8001

Please note that the Slave ID should be same with the ID in

“Operating Mode”. And then click “OK” enter the

application page.

«
...
32
33
34
35
36
...
»

Содержание KGW3101











































Отзывы:

Нет отзывов

Похожие инструкции для KGW3101

Бренд: Pace Страницы: 2

Бренд: RTA Страницы: 72

Бренд: ProSoft Technology Страницы: 86

Бренд: NeoGate Страницы: 41

Бренд: Inteno Страницы: 10

Бренд: SenseNet Страницы: 11

Korenix JetWave 2310 Series

Бренд: Beijer Electronics Страницы: 2

ASLINK B2G78-PB1

Бренд: Anywire Страницы: 50

Бренд: Aaeon Страницы: 20

Бренд: Internode Страницы: 12

Бренд: Planet Страницы: 30

Бренд: Tut Systems Страницы: 104

Бренд: Entone Страницы: 3

Entone 95-810500-00

Бренд: Entone Страницы: 14

F8926-GW Series

Бренд: Four-Faith Страницы: 78

Бренд: Technicolor Страницы: 82

Бренд: Technicolor Страницы: 81

Бренд: Lantronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды